DQ450DBZ XJ-450 3NB-1300F Drilling & Mud Pump Spare Parts

1. Core Product Orientation & Target Application

This full range of industrial-grade spare parts is precision manufactured for DQ450DBZ drilling systems, XJ-450 workover units, 3NB-1300F mud pumps, and supporting RS-F1600/F1300 hydraulic cylinders, BJX260 reducers, and FAMT-12T rear axle assemblies, covering high-pressure O-rings, sealing rings, bushings, valves, filters, hydraulic cylinders, electrical modules, gaskets and specialized wearing parts for Lanshou LS, Honghua, WAGO NOV branded supporting equipment. Target users include on-site drilling rig maintenance engineers, oilfield hydraulic & lubrication system technicians, dedicated equipment procurement specialists, field maintenance supervisors, and mechanical after-sales teams working in harsh oilfield environments—professionals routinely plagued by hydraulic fluid leakage, premature seal failure, bushing wear, clogged filters, mismatched spare parts, and unplanned equipment downtime caused by high vibration and extreme working conditions.

Core Purpose: All parts are direct interchangeable replacements produced in full compliance with GB3452.1, JB/ZQ42 24-97, ZQ203/100, Q/JC series and CNPC industrial standards, designed to restore equipment sealing performance, load-bearing capacity, hydraulic pressure stability and safe operation. These parts solve critical on-site pain points including high-pressure mud and oil leakage, short service life of wearing parts, seal degradation in extreme temperatures, and poor component compatibility, while providing a unified, standardized procurement benchmark and hands-on technical troubleshooting reference for field maintenance teams.

1.1 Product Introduction

This comprehensive spare parts portfolio covers all key vulnerable and structural components for oilfield drilling and workover equipment, including metric and standard O-rings, J-sealing rings, custom oil seals, bimetallic bushings, hydraulic cylinder rods, valve assemblies, filters, electrical modules, rubber hoses, gaskets and professional sealing packing. Sealing components are made from oil-resistant, high-pressure nitrile rubber and high-temperature Teflon materials; bushings and valve parts adopt high-strength bimetallic alloy and precision-forged steel; electrical and hydraulic parts fully match original equipment interface and performance parameters, with zero deviation in installation dimensions.

Exclusive factory and field test data: Standard O-rings and sealing rings maintain complete sealing under 36MPa continuous pressure for 3500 working hours; bimetallic bushings reach 60 HRC surface hardness, with a service life of 3200 operating hours under continuous friction; Teflon sealing packing resists mud erosion and high-temperature corrosion for 2800 hours; all rubber hoses and gaskets remain elastic and crack-free under -30℃ to 160℃ temperature fluctuations. Backed by decades of professional oilfield parts manufacturing experience and full third-party quality certification, each part undergoes 100% dimensional inspection, pressure testing and wear testing before leaving the factory, ensuring direct installation without on-site modification.

1.2 Function Description

High-pressure sealing parts including O-rings, oil seals and gaskets effectively block leakage of hydraulic oil, lubricating oil and drilling mud, maintaining stable system pressure; bimetallic bushings and cylinder rods reduce friction between moving parts, resisting wear and offsetting lateral deviation; valves and filters control fluid flow and purify hydraulic and lubricating media, preventing impurity blockage; rubber hoses and connectors realize safe transmission of fluid media; electrical modules and fieldbus couplers ensure stable signal transmission and equipment control; dust-proof rings and packers protect internal components from mud and dust intrusion, extending overall equipment service life.

1.3 Structural Features

Sealing parts adopt precision compression molding, with uniform wall thickness, high rebound resilience and perfect fit with sealing grooves, adapting to frequent pressure and temperature fluctuations; bimetallic bushings feature double-layer composite structure, combining high wear resistance and good thermal conductivity; valve components adopt precision grinding process, with small fit clearance and sensitive action; rubber hoses and fasteners feature anti-loosening and anti-corrosion design, maintaining stable performance under high-frequency vibration; all parts adopt standardized modular design, consistent with original equipment structure, enabling quick disassembly and replacement.

2. Applicable Operating Conditions

These spare parts are designed for extreme oilfield drilling and workover environments, suitable for land desert oilfields, cold region well sites and offshore operation platforms, operating stably in an ambient temperature range of -35℃ to 165℃. They can withstand high-pressure hydraulic circulation, heavy-load continuous operation, strong mechanical vibration, mud erosion and oil corrosion, fully meeting the operation requirements of DQ450DBZ, XJ-450, 3NB-1300F equipment and supporting hydraulic, transmission and braking systems. They are widely used in mud pump assemblies, hydraulic cylinder systems, drilling rig control units and auxiliary working devices, adapting to various harsh long-term operation conditions.

We supply the following spare parts:

3. Maintenance & On-Site Engineer Practical Suggestions

3.1 Routine Maintenance Tips

Inspect sealing rings, O-rings and gaskets every 45 operating hours, replacing aged, worn or cracked parts immediately to avoid fluid leakage; clean filter elements every 600 operating hours, replacing clogged filters to ensure smooth fluid circulation. Check bushing and cylinder rod wear every quarter, replenishing special high-temperature lubricating grease; tighten connecting fasteners monthly to prevent loosening caused by equipment vibration. For electrical modules and sensors, regularly remove surface dust to keep signal transmission stable, and avoid moisture intrusion into electrical components.

3.2 On-Site Maintenance Avoidance Guidance

Never reuse disassembled O-rings, gaskets and other disposable sealing parts, as disassembly permanently damages sealing performance; strictly match part models, standards and original part numbers during replacement, and do not use non-standard substitute parts. Relieve all system pressure before maintaining hydraulic cylinders and valves to prevent safety accidents; when replacing bushings and seals, ensure accurate alignment to avoid eccentric wear and partial pressure damage. Do not modify the structure of electrical modules and valves at will, so as not to affect equipment performance and safety certification.

4. On-Site Oilfield Fault Repair Cases

4.1 Sichuan Changning Shale Gas Drilling Site

Equipment Model: DQ450DBZ drilling system; Operating Load: 35MPa continuous mud pressure; Fault Issue: 2-228 56.74X3.53 O-ring wear, severe mud leakage, unstable system pressure. After repair: Replaced standard O-ring and matching gasket; Repair indicators: No leakage under 36MPa pressure, system pressure stable, continuous operation for 3400 hours. Customer Feedback: Thoroughly solved mud leakage problem, reduced emergency maintenance frequency, fully meeting on-site construction requirements.

4.2 Xinjiang Karamay Oilfield

Equipment Model: XJ-450 workover unit support hydraulic cylinder; Operating Load: 180-ton lifting load; Fault Issue: J-Sealing ring 100 JB/ZQ42 wear, cylinder pressure loss, slow action. After repair: Replaced standard J-sealing ring; Repair indicators: Cylinder pressure maintained stably, sensitive action, no pressure drop, sealing performance up to standard. Customer Feedback: Perfect size matching, quick replacement, restored cylinder working efficiency, adapted to desert harsh environment.

4.3 Bohai Offshore Oilfield Mud Pump Station

Equipment Model: 3NB-1300F mud pump; Operating Load: 24-hour continuous operation; Fault Issue: Bimetallic bushing GH3161-05.21 wear, pump body abnormal noise. After repair: Replaced standard bimetallic bushing; Repair indicators: Abnormal noise eliminated, bushing temperature stable, service life extended by 1100 hours. Customer Feedback: High-quality wearing parts, strong corrosion resistance, adapted to offshore salt spray environment, equipment operation returned to normal.

5. Frequently Asked Questions (FAQ)

6. Customer Procurement Guidance

For oilfield drilling and workover teams that need reliable, durable spare parts to reduce equipment failure rate, control maintenance costs and ensure continuous and safe operation in harsh environments, this full range of special spare parts for DQ450DBZ, XJ-450 and 3NB-1300F equipment is the optimal procurement choice. With complete models, strict compliance with industrial standards, superior wear resistance and long service life, these parts can meet both daily routine maintenance and emergency fault repair needs, eliminating the risks of model mismatch and inferior quality parts.

We sincerely welcome customers to provide detailed part numbers, equipment models and on-site working condition parameters, and we will provide a targeted accurate quotation, complete technical parameter documents and professional model selection guidance. Relying on strict production quality control and mature oilfield parts supply experience, we provide high-quality, stable and reliable spare parts to escort the efficient and safe operation of your oilfield equipment.

contact us ：

Emeil: [email protected]  

whatsapp: +86 15275658619