25 Jun 2026
F1300/F1600/3NB Series Pump & ZJ70DB/ZJ70DS Rig Replacement Components
1. Product Overview & Core Operational Value
Onshore and offshore oilfield drilling operations in Turkmenistan frequently face unplanned downtime caused by worn pump components, failed winch transmission parts, degraded sealing assemblies, and underperforming diesel engine spare parts. High-pressure drilling cycles, continuous mechanical vibration, extreme ambient temperature fluctuations, and abrasive mud circulation all accelerate component fatigue, leading to efficiency drops, safety hazards, and costly operational halts. This full set of drilling rig spare parts is custom-matched for mainstream drilling equipment including F-1300, F-1600, 3NB-1300F, 3NB-1600 drilling pumps, ZJ-70DB, ZJ-70DS, ZJ-30T drilling rigs, Doosan and CAT series diesel engines, and supporting manifold, BOP, and circulating system equipment. All components serve as direct replacement parts for routine maintenance, overhaul, and emergency breakdown repair, ensuring full mechanical compatibility and consistent field performance for oil and gas drilling workflows.
Core application scenarios cover high-pressure downhole drilling, mud circulation processing, power drive operation, wellhead pressure control, and mechanical transmission systems in harsh oilfield environments. Every spare part is engineered to resolve common field pain points: short service life of pump liners and pistons, brake system failure of drilling winches, hydraulic system leakage of top drive units, diesel engine power attenuation, and sealing failure under high-temperature and high-pressure working conditions.
2. Core Function & Structural Characteristics
Functionally, these rig spare parts undertake four core operational roles in drilling systems: power output support, pressure circulation stabilization, mechanical transmission synchronization, and safety pressure protection. Drilling pump accessories maintain stable mud displacement and pressure output to guarantee continuous downhole circulation; winch and top drive components ensure precise lifting, rotating, and positioning of drill strings; diesel engine and power drive parts sustain steady power output under long-duration load; BOP, manifold and wellhead accessories provide reliable pressure sealing and emergency pressure relief to avoid well control risks.
Structurally, all components adopt integrated modular design for quick disassembly and on-site replacement. Wearable parts such as cylinder bushings, polyurethane pistons, valve assemblies, and sealing rings follow standardized dimensional specifications to achieve universal interchangeability for matched equipment. Transmission components including drive shafts, gear sets, and bearing assemblies adopt precision machining structures to reduce friction loss and improve transmission efficiency. Hydraulic and pneumatic control parts feature compact sealing structures to adapt to high-vibration field working conditions and prevent medium leakage.
3. Applicable Working Conditions & Standard Compliance
This batch of spare parts is fully adaptable to complex oilfield working conditions, including onshore desert high-temperature drilling sites, offshore shallow-water drilling platforms, high-vibration continuous operation areas, and high-pressure downhole dangerous working zones. The components stably operate in ambient temperatures ranging from -40°C to +55°C, withstand maximum working pressure up to 70MPa, and support long-cycle continuous operation with 24-hour non-stop mechanical load. Key structural parts adopt alloy steel forging and polyurethane high-strength molding, with a material hardness of 280–320 HB and a fatigue life of over 50,000 continuous working cycles.
All products strictly comply with international industry certification standards: MSDS material safety specifications, EExd explosion-proof certification, UL safety standards, and ASME B18.3 precision machining standards. Fastener parts adopt a standard tightening torque of 85–120 N·m to ensure structural stability under high vibration. Pressure-bearing components pass 1.5 times rated pressure hydrostatic testing, with zero leakage after 3-hour continuous pressure holding, meeting mainstream oilfield construction and safety operation specifications.
4. On-Site Engineer Maintenance & Operation Suggestions
From on-site drilling operation experience, targeted maintenance can effectively extend the service life of rig spare parts and reduce failure rates. First, for drilling pump wearable parts (liners, pistons, valve assemblies), conduct daily visual inspection of abrasion and deformation, and replace components when surface wear exceeds 0.8mm to avoid mud pressure fluctuation. Second, for winch brake systems and transmission chains, complete lubrication supplementation every 200 working hours and check chain tension and brake band wear to prevent slipping and braking failure.
Third, for diesel engine filter elements, sealing rings, and belt components, implement regular replacement cycles according to load intensity; high-load operation scenarios require filter replacement every 300 working hours. Fourth, for high-pressure manifold and wellhead sealing parts, check gasket aging and thread tightness before each drilling shift to eliminate high-pressure leakage risks. Finally, all replaced waste parts shall be recorded and classified, and equipment operation data shall be archived to optimize subsequent spare parts stocking and maintenance cycles.
5. Core Product Advantage & Procurement Value Summary
This full set of Turkmenistan drilling rig spare parts features outstanding reliability, precise interchangeability, high safety performance, and extended service life. All components are produced with strict dimensional consistency control, achieving 100% matching assembly with corresponding F-series drilling pumps, ZJ-series drilling rigs, Doosan/CAT diesel engines, and supporting well control equipment. Compared with ordinary accessories, standardized raw material selection and precision processing effectively reduce fatigue damage under high load and high vibration, lowering equipment failure rate and overall operation and maintenance costs.
In terms of safety performance, all pressure-bearing and explosion-proof parts pass professional third-party testing, fully adapting to high-risk high-pressure and high-temperature drilling environments. The modular design greatly shortens on-site replacement time, reduces equipment downtime, and significantly improves drilling operation efficiency. This spare parts list covers full-series wearable and vulnerable components of core drilling equipment, providing comprehensive technical and material support for daily maintenance, equipment overhaul, and emergency repair of Turkmenistan oilfield drilling rigs.
6. Dual Standards: Procurement Selection & On-Site Maintenance Judgment
6.1 Procurement Selection Standard
First, dimension matching: Verify component caliber, length, installation thread specification, and assembly size strictly according to the original equipment model to ensure zero assembly error. Second, material standard: Wearable parts adopt high-strength polyurethane and alloy wear-resistant materials; pressure-bearing parts use carbon steel and alloy forging materials; sealing components adopt oil-resistant, high-temperature resistant rubber and polymer materials. Third, certification standard: Prioritize products that meet MSDS, EExd, UL and ASME B18.3 standards with complete test reports. Fourth, model adaptation: Strictly classify and select parts according to equipment models including F-1300/F-1600 pumps, ZJ70DB/ZJ70DS rigs, Doosan PU222TI and CAT series diesel engines to avoid model mismatch.
6.2 On-Site Fault Judgment & Repair Standard
For drilling pump faults: If mud pressure fluctuates by more than 10% and displacement drops abnormally, check liner wear and valve assembly sealing, replace damaged wearable parts, and test pressure to restore stable output. For winch system faults: Abnormal noise during lifting or delayed braking response indicates friction reel, brake band or transmission chain wear, requiring timely replacement and lubrication calibration. For diesel engine faults: Power attenuation and increased exhaust smoke signal filter blockage or sealing ring aging, needing filter replacement and air tightness detection. For wellhead manifold faults: Micro-leakage under high pressure indicates aging of sealing gaskets and flexible connectors, requiring immediate replacement to eliminate safety risks.
7. On-Site Fault Repair Case Verification
Case 1: Onshore Desert Drilling Site – F-1600 Drilling Pump Liner Failure
At a Turkmenistan onshore desert drilling site, the F-1600 drilling pump operated under 32MPa continuous working pressure for 450 hours, resulting in 1.2mm liner abrasive wear, obvious mud pressure fluctuation, and 18% drop in drilling fluid displacement. After replacing the matched ø160mm cylinder bushing spare part, the pump’s working pressure stabilized at 32–33MPa, displacement recovered to standard rated value, and continuous stable operation was achieved for another 600 hours. The on-site engineering team feedback confirmed that the replacement part features high wear resistance and perfect assembly compatibility, completely resolving frequent pressure fluctuation faults.
Case 2: Offshore Drilling Platform – ZJ70DS Winch Brake System Fault
A Turkmenistan offshore shallow-water drilling platform’s ZJ70DS drilling rig winch had delayed braking response under 80% rated load after long-term high-vibration operation, with a braking error of 2.3 seconds. After replacing the matched brake band and electromagnetic brake accessories, the braking response time was restored to the standard 0.8 seconds, and no slipping or delayed braking faults occurred in subsequent 300-hour continuous lifting operations. The site confirmed that the accessories have stable friction performance and strong adaptability to offshore humid and high-vibration environments.
Case 3: Oilfield Power Station – Doosan PU222TI Diesel Engine Power Attenuation
A Turkmenistan oilfield power supporting station’s Doosan PU222TI diesel engine suffered power attenuation of 12% after 500 hours of high-load operation, accompanied by increased exhaust smoke. After replacing dedicated oil filters, fuel filters and sealing ring accessories, the engine power was fully restored to 588kW rated power, exhaust emission reached standard values, and no power attenuation fault occurred in long-term continuous operation. The maintenance team verified that the filter accessories have high filtration precision and effectively protect engine internal components.
Case 4: High-Pressure Wellhead Operation – BOP Sealing Component Leakage
In a high-pressure well control operation in Turkmenistan oilfield, the 13 5/8” BOP equipment had micro-leakage at the sealing position under 50MPa working pressure, posing potential well control risks. After replacing the matched BOP sealing ring and wedge packer accessories, the equipment passed 3-hour 50MPa static pressure test with zero leakage. The on-site team confirmed that the sealing parts have excellent high-pressure resistance and aging resistance, fully meeting harsh wellhead operation requirements.
8. Frequently Asked Questions (FAQ)
No. | Question | Professional Answer |
1 | Are these spare parts fully compatible with old and new versions of ZJ70 series rigs and F-series pumps? | All accessories are designed for full compatibility with ZJ70DB (2010/2015), ZJ70DS (2002) rigs and F-1300/F-1600/3NB series pumps. Standardized dimensional design ensures interchangeability for old and new equipment versions without modification. |
2 | What is the standard replacement cycle for wearable parts like pump liners and pistons? | Under conventional 24MPa–35MPa working pressure, the replacement cycle for cylinder bushings and polyurethane pistons is 400–600 working hours; under high-pressure (≥50MPa) heavy load conditions, the cycle is shortened to 300–400 hours, and immediate replacement is required if wear exceeds 0.8mm. |
3 | What certifications do these drilling rig spare parts hold for oilfield operation? | All core components comply with MSDS material safety specifications, EExd explosion-proof standards, UL safety certification and ASME B18.3 precision machining standards, with complete factory test reports and material traceability documents, meeting international oilfield operation requirements. |
4 | Is professional tooling required for on-site installation and replacement? | Most wearable parts and standard components support quick on-site replacement with conventional oilfield maintenance tools. Individual precision transmission components and hydraulic parts require standard torque tools for installation according to specified torque parameters to ensure assembly accuracy and operational stability. |
Turkmenistan rig spare parts list
No./p | Product name | Brand and GOST of the product |
1 | 2 | 3 |
LOT #2 | ||
Main drilling, power and technological equipment | ||
1 | Drilling pump “F-1300” (China) | AH130101.00 |
2 | Drilling pump “F-1300” with diesel drive “WEICHAY” with a capacity of more than 1000 hp with a reduction gear 1.53 and a clutch LT-600-250 with a transmission belt, installation supervision (China) | |
3 | F-1600 drilling pump for ZJ-70 DB rig (BOMCO 2015) (China) | |
4 | F-1600 drilling pump with electric motor on frame for ZJ-70 DS installation, installation supervision (2002) (China) | |
5 | Drilling pump 3NB-1300F with diesel drive “WEICHAY” with the capacity of more than 1000 hp with reduction gear 1.53 and coupling LT-600-250 with transmission belt, installation supervision (China) | |
6 | Manifold of drilling pump “ZG-100×35-S” 35 MPa (ground type with manual drive with thread FIG-1003 (China) for drilling rig URALMASH-3D-76 | BC080112-5000 |
7 | Manifold of drilling pump MBU-2U or similar | |
8 | Circulation system ZYG-200m3 (capacity -240m3/hour, productivity -200m3/hour) (China) | |
9 | Swivel SL-450-5 (China) | 104.16.00 |
10 | Swivel XSL-225 (China) | XSL-225 |
11 | Auxiliary air winch (China) | XJFH5/35 |
12 | Winch LBU-1200 or similar | 4062.90.100 |
13 | Winch JC-70 DS (for installation ZJ-70DS 2002), installation supervision (China) | JC-70DS |
14 | Diesel engine “G12V190PZL1”, installation supervision (China) | «G12V190PZL1» |
15 | Diesel CO 1000F/30 (ser 190) (G12V190PZL) | |
16 | Diesel engine “SAT C-15” (oil), installation supervision (USA) | MCW1-Up |
17 | Diesel “SAT-3512V” RTM with a radiator core with a seal (4 cores with a seal 1 set) | |
18 | Doosan diesel engine for drilling rig drive (PU222TI588KW(800PS)/2100RPM) (South Korea) | |
Technical parameters and configuration for 1 (one) set of Doosan diesel engine: | ||
18.1 | Power 588 (800)/2100(kw(ps)/rpm) | |
18.2 | V12 cylinder four stroke diesel engine | |
18.3 | Speed 1500 rpm. Displacement 21.927 | |
18.4 | Engine with fan and radiator. Radiator for cooling will be supplied for each engine separately | |
18.5 | SAE1 housing | |
18.6 | Flywheel 14″ | |
18.7 | Oil and fuel filter. Will be installed in every engine | |
18.8 | Flexible exhaust pipe (for connection to mufflers). Will be supplied for each engine in individual packaging. | |
18.9 | Fuel lift pump. Installed in every engine. | |
18.10 | Starter 24V/7kW. Will be installed in each engine | |
18.11 | Generator 24V/45A. Will be installed in each engine | |
18.12 | Bosch high pressure fuel pump. Will be installed in every engine | |
18.13 | Variable speed controller. Will be installed in each engine. | |
18.14 | Electric control panel. Will be supplied in individual packaging for each engine. | |
18.15 | Two silencers with spark arrestors, including mounting parts (counter flanges, seals, bolts and nuts). Will be supplied for each engine in individual packaging. | |
18.16 | Additional coarse fuel filter. Will be supplied for each engine in individual packaging. | |
18.17 | Hand pump for pumping out oil when changing it. Will be supplied for every 3 engine sets, 1 piece. | |
18.18 | Vibration dampers (shock absorbers). 6 pieces will be supplied for each engine kit. | |
18.19 | Coupling assembly (coupling, shaft, intermediate plate (flange) and other fastening devices). RM5000 Chinese version with the appropriate dimensions for the customer and for each 1 engine, 1 piece. | |
18.20 | Operation manual for every 5 diesel sets – 1 manual. In English and Russian | |
Additional spare parts for diesel engine “DOOSAN PU 222 TI” | ||
18.21 | Oil filter 65.05510-5020V (2 pcs in a set) | |
18.22 | Fuel filter 65.12503-5016B or 65.12503-5019 (2 pcs in a set) | |
18.23 | Motor oil, Antifreeze and battery by volume and quantity | |
18.24 | Air filter 65.08304-6005 (2 pcs in a set) | |
19 | Diesel Generator 300KWawith engine “Doosan Korea” in a closed container, with a filter for 1 year (Korea) | |
20 | Rotor ZP-275, with sprocket Z=23 (China) | ZP 000000 AG275000100-SM |
21 | Rotor ZP-375 (China) | 105.08.00 |
22 | Rotor P-700, with sprocket Z=19 or similar | 14016.45.000-01 |
23 | Air compressor “Sullair” with electric motor (China) | LS 12-50HHAC |
24 | Air compressor 4VU1-5/9 M4UHL4 or similar | GOST 2405-88 14040.70.150 |
25 | Compressor station VU1-5/9 M4UKHL4 or similar | 4062.70.600 |
26 | Air compressor, piston P=1.0 MPa (China) | |
27 | Degasser ZGQ 1/4 (China) | TU39-01-08-677-81 |
28 | Degasser “Cascade-40” or equivalent | |
29 | Transmission box “Allison-S5610H” (China or USA) | 29537462 |
30 | Transmission box “Allison-S5620AR” (China or USA) | 29537301 |
31 | Gearbox ZPCDX-00 for rotor drive ZP-275 “XJ-750” | Kerui Group |
32 | FKQ-8000-6 control station with flexible hydraulic lines (China) | |
33 | Control station СН6U-76 “Upetrom” 2-battery (Romania) | 430-32.00.00.00.0 |
34 | Pipe threading machine with extended bed 1N983. 16 kW or similar | GOST 631-79 |
35 | Screw-cutting lathe | 16K40 |
36 | Vertical drilling machine | 2N135 |
37 | Heavy-duty tracked vehicle TGP-70 or similar | TGP-70.02.01.000 |
38 | Transport trolley TP-35 or similar | TP-35.00.000 |
39 | Crane KPB-3M or equivalent | GOST 22584-77 |
40 | Rotary drilling crane, capacity 5t, height L=.6m (China) | |
41 | Vibrating sieve S250-1 (China) | |
42 | Vibrating sieve S250-2 (China) | |
43 | Clay mixer NJ-4m3 single-shaft (China) | |
44 | Travelling block YC-225 (China) | |
45 | Hook DG-225 (China) | |
46 | Vertical Slurry Pump (China) | 100YZS 150-700 |
Spare parts for JC70D drilling winch for ZJ70DS drilling rig (2002) (lot indivisible) | ||
47 | Auxiliary Winch Brake Control System JC-70D (China) | |
48 | Electromagnetic brake (hydromat) for winch JС-70DS (2002) (China) | FC 020000 |
49 | Electrodynamic brake disc JC-70D (China) | P.S. 060000 |
50 | Surge arrester valve M12x1.5 | |
51 | Relief valve (3/4NPT) | |
52 | Main drive shaft assembly | 106.16.37.00 |
53 | Intermediate shaft assembly | 106.16.40.00 (106.23.40.00) |
54 | Friction reel for winch | JC-70 |
55 | Gear oil pump for lubrication of winch SВ100 | ZX09 |
56 | Oil pump chain for power unit drive | |
57 | 2-way valve of the driller’s control panel | |
58 | Drive chain, roller, 10 meters | 32S-2x |
59 | Drive chain, roller, 10 meters | 32S-4x |
60 | Drive chain, roller, 10 meters | 24S-6x |
61 | Drive chain, roller, 10 meters | 24S-3x |
62 | Brake band JC-70DS | |
Spare parts for drilling winch JC70DB for drilling rig ZJ70D (2010) ZJ70DB (2015) | ||
63 | Water-cooled brake disc for winch JC-70D (2010) (BOMСO) | |
64 | Hydraulic pump of the brake system of the winch JC-70D (2010) | Rexroth D-72150 Horb 10V |
65 | Splined connection between electric motor and gearbox for winch JC-70DB | |
66 | Splined connection between electric motor and gearbox for rotor ZP-375 | |
67 | Splined connection between electric motor and pulley for F-1600 pump | |
68 | Toothed oil pump | YB040013 |
69 | Axial piston pump JGBOY-BL | YB040013 |
70 | Chain wheel Z=34, P=38.1 3-row | ZZ070004 |
71 | Brake disc for winch JC-70DB (2015) without water cooling | |
72 | Pneumatic compensators for the control panel of the hydraulic pump of the brake system with valves for the ZJ-70DV installation for the JC-70DV winch (2015) | |
73 | Brake slave cylinder (caliper) for winch JC 70 DB | PS010000 |
74 | Safety brake cylinder (support) for winch JC 70 DB | PS020000 |
75 | Explosion-proof oil pump unit LWBZ-200 | JC110100 |
76 | Brake band | ZQ050100 |
77 | Ballonet | ZQ030025 |
78 | Ballonet | ZQ030043 |
Top drive DQ 70BS-JH (2015) (lot is indivisible) | ||
79 | Thrust tapered roller bearing | W0106234 max3 |
80 | Thrust tapered roller bearing | W0106292 |
81 | Cylindrical roller bearing(3520) | W0101100 |
82 | Spherical roller bearing (24122) | W0102110 |
83 | Cylindrical roller bearing | W0101220 |
84 | Cylindrical roller thrust bearing | W0103181 |
85 | Cylindrical roller thrust bearing | W0103260 |
86 | Cylindrical roller bearing | W0101180 |
87 | Rotary seal gland 180x210x15 | M09180 |
88 | Rotary seal gland 210x240x15 | M09210 |
89 | Seal of mud pipe 127×95 | NT75401030 810 |
90 | Central pipe 95×250 | NT754010308-VI |
91 | Flushing pipe assembly 35 mPa | NT7540103 08 |
92 | Sling 350 t | W03350108 |
93 | Pipe clamp jaw | T7540205081 |
94 | Carrier roller assembly | T7503153201 |
95 | Hydraulic pump unit YB015.537 | M2JA132 M6B B35 A37-FR-O1-H-SK |
96 | Hydraulic motor with gear | YBO3315+06 |
97 | Bell-shaped casing | YB0701 |
98 | Coupling | YB0801+A9 |
99 | Coupling | YB0803 |
100 | Skating rink | YB0703 |
101 | Lubrication motor complete with gear pump YB021.140 | M2JA90LM6A+HGP-3A-F40R |
102 | Return oil filter | YQ0203160100 |
103 | Return oil filter housing | YQ020316 01002 |
104 | Transmission oil filter | YQ0103160 |
105 | High pressure filter for hydraulic oil | YQ0102063 |
106 | First leading gear | 70010401 |
107 | Second drive gear assembly | 70010403 |
108 | Second driven gear | 700104013 |
109 | Small gear of the rotating adapter | T75020106 |
110 | Seal for main shaft (ø210х78) | T7540104082 |
111 | Seal for main shaft (ø210х164) | T7540104060 |
112 | Under the dense envelope – lower sealing sleeve (ø210×60) | 700104311 |
113 | Under the dense envelope – lower sealing sleeve (ø210×70) | 700104312 |
114 | Hydraulic cylinder for tilting the link assembly | DQ70BS-GZ-03 |
115 | Locking device assembly | DQ70BS-GZ-04 |
116 | Stopper die | T75020403 |
117 | IBOP Management | DQ70BS-GZ-06 |
118 | Plunger pump | YB05037 37cm3/r |
119 | Gear pump | HGP-3A-F30R-2B |
120 | Gear pump | HGP-3A-F40R |
121 | Ball bearing 480x380x46 | W0104380 |
122 | Hydraulic auxiliary system valve block | YFT754BOOO |
123 | Mud hose with thread 4”x35mPa -23m FIG-1003 | 20130613006 |
Spare parts for drilling pump F-1300, F-1600 (lot indivisible) | ||
124 | Cylinder bushing ø130 mm | AH000003031200 |
125 | Cylinder bushing ø140 mm | AH000003031300 |
126 | Cylinder bushing ø150 mm | AH000003031400 |
127 | Cylinder bushing ø160 mm | AH000003031500 |
128 | Cylinder bushing ø170 mm | AH000003031600 |
129 | Cylinder bushing ø180 mm | AH000003031700 |
130 | Piston polyurethane ø130 mm | AH 0000040300 |
131 | Piston polyurethane ø140 mm | AH 0000040500 |
132 | Piston polyurethane ø150 mm | AH 0000040600 |
133 | Piston polyurethane ø160 mm | AH 0000040700 |
134 | Piston polyurethane ø170 mm | AH 0000040800 |
135 | Piston polyurethane ø180 mm | AH 0000040900 |
136 | Runner rod | AH 1301010516 107.11.01.02 |
137 | Valve body | 107.11.140.00 |
138 | Valve seat | 107.11.140.04 |
139 | Valve rubber polyurethane (plate) | |
140 | Valve holder (upper) | AH 36001-05A04.00 |
141 | Valve holder (lower) | AH 130101050 500 |
142 | Bronze insert valve holder upper | |
143 | Crosshead rod seal | F-1300, F-1600 |
144 | Crosshead lining | RS 11309.04.012 |
145 | Crosshead bearing | RS 11309.04.015 |
146 | Diaphragm of pneumatic compensator KW-75 | AK 75350100 |
147 | AVB coupling cylinder 600×250 semicircular shape | W190C300A9 |
148 | Cylinder block 600×250 (overlay) | |
149 | Hydraulic Cylinder Assembly (F-1600) | AH130102050100 |
150 | Piston rod with clamp assembly | 107.11.110.39 NB050015 |
151 | Half-rod seal | 107.11.96.00 |
152 | Cylinder Liner Seal (F-1600) | 107,11,110.42 |
153 | Valve Cover Seal (F-1600) | 107,11,330.00 |
154 | Hydraulic cover seal (front) polyurethane | |
155 | Pneumatic swivel QFS-15 | |
156 | Surge arrester KRJa-1.15 | |
157 | V-belt A3708 L=8000mm | HGT-2819 |
158 | Gear oil pump LWBZ-40/6 (50HZ) | BZ040100 |
159 | Clay solution gate valve (forging) | BZ080100 |
160 | V-shaped tubular filter VWU-100x180J | BZ040013 |
161 | Shear pin safety valve JA-3 (flanged) | NB110000 |
162 | Vibration-resistant pressure gauge 60 mPa, 8700 PSI (21/16-5000) | NB000032 |
163 | Valve spring (F-1300, F-1600) | NB050007 |
164 | Ferrule | AH1301010513 XC2013075 |
165 | Eccentric bearing NUP46477Q4/C9YA4 | NB020020 |
166 | Main Bearing 24060CA/CAW33 | NB02010021 |
167 | Bearing NU3044x3M/CA | NB030014 |
168 | Leading bearing | RS 11310.04.008 |
169 | Leading Bearing Box (Left) | RS 11310.01.005 |
170 | Leading bearing box (right) | RS 11310.01.001 |
171 | Bearing 4G312844H | RS 11309/03/012 |
172 | Bearing 32338 W33 transmission shaft (F-1300) | |
173 | Bearing 32848 W33 lower (F-1300/1600) | NU2148X3M/C9 |
Spare parts for drilling pump F-800, F-1000 (lot indivisible) | ||
174 | Cylinder bushing ø 150 mm | |
175 | Cylinder bushing ø160 mm | |
176 | Cylinder bushing ø170 mm | |
177 | Piston ø150 mm | |
178 | Piston ø160 mm | |
179 | Piston ø170 mm | |
180 | Hydraulic cylinder assembly F-800,F-1000 | |
181 | F-1000 Crosshead Half Rod Seal | RS 11306.04.007 |
182 | Crosshead rod seal 4x5x0.5mm ass. | FR0801010414 |
183 | Crosshead ram rod F-800, F-1000 | |
184 | Valve seat | |
185 | Valve plate | |
186 | Rubber valve element | |
187 | Piston rod F-800, F-1000 | RS 11306.05.017 |
188 | Valve holder (upper) | RS 11.308.05.010 |
189 | Valve holder (lower) | RS 11308.05.026.01 |
190 | F-1000 Runner Rod Seal Holder Cover | RS 11308.05.04.003 |
191 | V-belt 5ZV25J-8000 mm F-800 | |
192 | V-belt 5ZV25J-8500 mm F-1000 | BZ000004 |
193 | Main bearing 3G3003748H (F-800/F-1000) | NB020023 |
194 | Eccentric bearing 928x508QU | (F-800/F-1000) |
195 | Transmission shaft bearing (F-800/F-1000) | NB030012 |
196 | Crosshead bearing (F-800/F-1000) | NB040021 |
197 | Lower bearing (F-800/F-1000) | |
Spare parts for drilling pump 3NB-1600 (lot indivisible) | ||
198 | Nest | 107.11.140.04 |
199 | Valve | NB050400 |
200 | Valve rubber polyurethane (plate) | |
201 | Compensator | 3NB-1600 |
202 | Oil pump with electric motor | 3NB-1600 |
203 | Water pump with electric motor | 3NB-1600 |
204 | Valve holder (lower) | 3NB-1600 |
205 | Hydraulic cylinder | 3NB-1600 |
206 | Cylinder liner seal | 3NB-1600 |
207 | V-belt | 3NB-1600 |
208 | Half-rod seal | 107.11.96.00 |
209 | cylinder bushings f 140 mm. | 107.11.110.27 |
210 | cylinder bushings f 150 mm. | 107.11.110.28 |
211 | cylinder bushings f 160 mm. | |
212 | cylinder bushings f 170 mm. | |
213 | cylinder bushings f 180 mm. | |
214 | cylinder bushings f 190 mm. | |
215 | piston f 140 | 107.11.00 |
216 | piston f 150 | 107.11.00 |
217 | piston f 160 | 107.11.00 |
218 | piston f 170 | 107.11.00 |
219 | piston f 180 | 107.11.00 |
220 | piston f 190 | |
Spare parts for swivel SL-450-5 (lot indivisible) | ||
221 | Main bearing 270x550x130 (19954EQ) | SL 000036 |
222 | Upper bearing 200x310x70 (2007140) GB/T-297 | SL 000031 |
223 | Lower bearing 240x360x56 (32148) GB/T-283 | SL 000039 |
224 | Mud pipe cuff | 104.05.30.08 |
225 | Mud pipe assembly | 104.05.30.00 |
226 | Feeding tube | 104.05.30.03 |
227 | Spring O-ring (upper) PD220x260x18 mm | HG4-692-67 |
228 | Spring sealing ring (lower) PD250x290x18 mm | HG4-692-67 |
229 | Feeding tube sealing ring (upper) | 104.05.30.01-1 |
230 | Feeding tube sealing ring (lower) | 104.05.30.06-1 |
231 | Gasket – washer | 104.05.15-1 |
232 | Upper bushing for swivel SL-450 | AD 4500010506 |
233 | Bottom bushing for swivel SL-450 | AD 4500010508 |
Spare parts for swivel SL-225 (lot indivisible) | ||
234 | Main bearing 9019456Q | SL 225-29.00 |
235 | Upper bearing 32040X2 (SL 000014) | GB/T-297-94 |
236 | Lower bearing NU240 (SL 000018) | GB/T283-2007 |
Spare parts for rotor ZP-375 (lot indivisible) | ||
237 | Rotor drive shaft ZP-375 | |
238 | Input shaft assembly | ZP030000 |
239 | Seal SG180x210x15 | ZP030018 |
240 | Seal SG180x220x18 | SG180x220x18 |
241 | Seal PG150x180x16 | ZZ040234 |
242 | O-ring 1049.5×8.6 | ZP030005 |
243 | O-ring 407×8.6 | ZP050002 |
244 | Small umbrella gear | ZP030001 |
245 | Stainless steel wire ø1.6 | ZP000039 |
246 | bearing NU2330M/C3 | ZP030019 |
247 | bearing 22330CA/C3W33 | ZP030020 |
248 | bearing 2687/1049 | ZP010009 |
Spare parts for rotor ZP-275 (lot indivisible) | ||
249 | Rotor drive shaft ZP-275 Chain wheel P=50.8 Z=23 | |
250 | Chain wheel P=50.8 Z=21 | ZP000012 |
251 | Chain wheel P=50.8 Z=23 | |
252 | Chain wheel (sprocket) P=50.8 Z=25 | ZP00000 |
Spare parts for diesel engine “G12V190PZL1” (lot indivisible) | ||
253 | Water cooling radiator | JC2112-1301-199-200 |
254 | Step-down gearbox 1.53, 900 kV, 1500-1 (1275x1085x980) | JS-1200 |
255 | Pneumatic starter (pneumatic motor) | 12VB.46.120F |
256 | Pneumatic fuel pre-supply pump | 12VB.54.00С |
257 | Pneumatically controlled valve “JDEC” G12V190PZL1″ | 12VB.46.300.10 |
258 | Oil controller bushing “JDEC” G12V190PZL1″ | Z12V.12.40.01 |
259 | Spring “JDEC” G12V190PZL1″ | Z12V.12.12.14A |
260 | Washer “JDEC” G12V190PZL1″ | Z12V.12.01A |
261 | Setting automatic brakes for low oil pressure | 12VB.34.00A |
262 | Fuel pump regulator “JDEC”G12V190PZL1” | T300/750Z |
263 | Tachometer with sensor “JDEC” G12V190PZL1″ | 12VB.32.00D |
264 | Water pump | 12VB.22.00V |
265 | Fuel pump | ВН6Z140ZP |
266 | Injector with sprayer assembly | 12 VВ.16.20E |
267 | Oil filter | 12 VB.18.10B |
268 | Fuel filter | 12 V.10.30.03 |
269 | Air filter (upper) | 12 V.36M.40 |
270 | Air filter (lower) | 12 V.36M.50 |
271 | Cardan clutch assembly | W51.5×870 |
272 | Turbocharger | J170-1 20GJ.00E |
273 | Cylinder head gasket (sealing ring II) | 12VB.03.12A |
274 | Fuel Pump Plunger Spring Clutch | Z12V.12.20 |
275 | Clutch plunger with fuel pump spring | Z12V.12.30 |
276 | Super Speed Safety Assembly | 12VB.37.00 |
277 | Plunger pair complete with spring | |
Drilling rig ZJ-30T. Spare parts for winch JS-30OC (lot indivisible) | ||
278 | JC-30 winch lifting shaft | ZJ-30T |
279 | Auxiliary winch XJFH-5×35 | JC-30 |
280 | Combined transfer case for power system | DL 050000 |
281 | Oil pump assembly for the “Allison-S5610NR” gearbox | 6880125 |
282 | Hydraulic pump NS with power take-off assembly | ZJ-30T |
283 | Drive chain, roller 44.45 mm 10 meters | 28S-2 |
284 | Connecting cylinder W31-20-901DDW1057 410010020 90 | ZJ-30T,XJ-750 |
Spare parts for lifting unit XJ-750 (lot indivisible) | ||
285 | Oil pump for the Allison-M5620R gearbox | 6880125 |
286 | XJ-750 Mast Lifting Hydraulic Cylinder | YGQB-262/1900 |
287 | Hydraulic pump “PARKER” PMD Çhemnitz Germany Part (НШ-XJ-750) | 7049112042 |
288 | Cardan shaft SС ВН-YMZG180С-1355 +60 21KN | JB/T5513-2006 |
289 | Cardan shaft SWC VN-YMZG180С-1370 +60 21KN | JB/T5513-2006 |
290 | Cardan shaft SС ВН-YMZG180С-1600 +60 21KN | JB/T5513-2006 |
291 | Cardan shaft SС ВН-YMZG180С-1755 +100 21KN | JB/T5513-2006 |
292 | Cardan shaft SС ВН-YMZG180С-18750 +60 21KN | JB/T5513-2006 |
293 | Cardan shaft cross fork of rotor drive | SWC 180 (21KN) |
294 | Winch lifting shaft JC-28/11 | XJ-750 |
Spare parts for the circulation system (lot indivisible) | ||
295 | Double-leaf valve FD DN80 1.0 MPa | |
296 | Double-leaf valve FD DN100 1.0 MPa | |
297 | Double-leaf valve FD DN150 1.0 MPa | |
298 | Double-leaf valve FD DN200 1.0 MPa | |
299 | Double-leaf valve FD DN250 1.0 MPa | |
300 | Double-leaf valve FD DN300 1.0 MPa | |
301 | Soft rubber connection KHT-DN100 | |
302 | Soft rubber connection KHT-DN150 | BZ070023 |
303 | Soft rubber connection KHT-DN200 | BZ070024 |
304 | Soft rubber connection KHT-DN250 | |
305 | Soft rubber connection KHT-DN300 | |
306 | Seal of the drilling manifold connection ZG-100×35 mPa | GK 010022 |
307 | Stirrer HMG-80 with gearbox, without electric motor | GK 010100 |
308 | Mixing device 11 kW, without electric motor | JQ110000 |
Spare parts for high pressure drilling manifold ZG 102-35 (lot indivisible) | ||
309 | High pressure gate valve 2” x35 MPa FIG -1002 | JC 150000 |
310 | High pressure gate valve 3” x35 MPa FIG-1003 | JC 020000 |
311 | High pressure gate valve 4” x35 MPa FIG -1003 | JC 100000 |
312 | Drilling hose 4” x35 mPa FIG-1003, 17.5 meter FIG-1003 | |
313 | Drilling hose 4” x35 MPa FIG-1003, 19 meter FIG-1003 | |
314 | Drilling hose 4” x35 MPa FIG-1003, 23 meter FIG-1003 | |
315 | Ground sleeve 4″*35 MPa -5m FIG-1003 | GH0000019 |
Spare parts for the compressor “Sullair” (lot is indivisible) | ||
316 | Oil filter | 02250054-605 |
317 | Water separating filter | 02250100-753 |
318 | Secondary filter | 02250100-754 |
319 | Air filter | 12P/N 049301 |
320 | Dehumidifier “SULLAIR” of air pneumatic system | QK000000»50N (37 kV) |
Spare parts for diesel engine “Doosan” PU 222TI (lot indivisible) | ||
321 | Cylinder assembly “DOOSAN” PU222TI | 65.01201-0312C |
322 | Pipe loader “DOOSAN” | 65.09100-7052 |
323 | Pipe loader “DOOSAN” | 65.09100-7153 |
324 | Generator 24V | 65.26101-7153B |
325 | Starter 24V | 65.26201-7074 |
326 | Cylinder head gasket “DOOSAN” | 65.03901-0069 |
327 | Water pump assembly | 65.06500-6148С |
328 | Shaft with bearing of water pump | 65.93410-0087 |
329 | Water pump mechanical seal | 65.06520-6007 |
330 | Fan belt (V-BELT) L=1425х9.5 | |
331 | Fan belt (V-BELT) L=1450х12,5 | |
332 | Fan belt L=1350×9.5 | |
333 | Alternator belt (V-BELT) L=1285х9.5 | |
334 | Alternator belt (V-BELT) L=1300х12.5 | |
335 | Oil filter element | 65.05510-5020B |
336 | Fine fuel filter “DOOSAN” PU 222 TI | 65.12503-5016B |
337 | Oil radiator | 65.05601-7135 |
338 | Water radiator “DOOSAN” PU 222 TI | 440211-00193 |
339 | Water radiator “DOOSAN” PU 222 TI 060/TBA | 65.06100-8032 |
340 | Injector with sprayer assembly | 65.10101-7053 |
341 | Water pump gasket | 65.06901A0074 |
342 | Piston “DOOSAN” PU 222 TI | 65.02501-0708 |
343 | Piston rings | 65.02503-0131 |
344 | Connecting rod “DOOSAN” PU 222 TI | 65.02401-0012 |
345 | Main shaft insert | 65.01110-6529 |
346 | Crankshaft assembly | 65.02101-7112 |
347 | Connecting rod insert “DOOSAN” PU 222 TI | 65.02410-0100 |
348 | Connecting rod insert “DOOSAN” PU 222 TI | 65.02410-0200 |
349 | High pressure fuel pump assembly | 65.11101-7334 |
350 | Oil pump “DOOSAN” PU 222 TI | 65.05100-6043A |
351 | Air filter element | 65.08304-6005 |
352 | Cooling thermostat “DOOSAN” PU222T | 65.06402-0006 |
353 | Oil cooler seal “DOOSAN” PU 222 TI | 65.05901-0014 |
354 | Control panel of devices “DOOSAN” PU222TI | 65.061700-6031B |
355 | Diesel engine sensor “DOOSAN” PU222TI | 65.27161-6001 |
356 | Tachometer sensor (on the flywheel) “DOOSAN” PU222TI | 65.27103-7007 |
357 | Oil pressure sensor “DOOSAN” PU 222 TI | 65.27431-6004 |
358 | DOOSAN piston pin” PU222TI | 65.02502-0081 |
359 | Connecting rod bushing DOOSAN” PU222TI | 65.02405-1008 |
Spare parts for power drive (analogue is considered) (lot is indivisible) | ||
360 | Cardan shaft clutch “VOITH” 12502463210 | K060.199.1034.N50 |
361 | Cardan shaft 125.024605100A | G040 1644 |
362 | Friction ring 125.01869110 | K060.057.0020 |
363 | Friction disc 125.0175580001 | K060.055.0021 |
364 | Highly elastic coupling 125.0157030001 | K060.152.0415.N50 |
365 | Connecting element 125.0079620001 | K060.050.1037 |
366 | Cardan crosspiece with clutch bearing “VOITH” | DIN 71412 |
Spare parts for the power unit of the ASDU or similar (lot is indivisible) | ||
367 | Power reducer (step-down) RCS-1.53 rpm-1500 | 4062.38.000 |
368 | I-st shaft of the power reducer RCS-1.53 | 4062.38.010 |
369 | II-nd shaft of the power reducer RCS-1.53 | 4062.38.012 |
370 | Drive shaft KPZ-900-D N III in sb | |
371 | Driven shaft KPZ-900-D N IV in the collection | |
372 | Shaft KPZ-900-D NI in sb | |
373 | Gearbox KPZ-900-U1 3D | 4062.10.500 |
374 | Oil pump KPZ-900-D with drive to the gearbox | type G11-25 |
375 | Twin transmission pulley (shaft) from the power unit ASDU-2SH-KP-U2 | 4062.08.000-1 |
376 | Single transmission pulley (shaft) from the power unit ASDU-1SHK-500-U2 | 4062.17.200 |
377 | Single transmission pulley (shaft) from power unit ASDU-2SH-500/580-U2 or equivalent | 4062.15.100 |
378 | Single transmission pulley (shaft) from power ASDU-2SH-500/580-U2 unit | 4062.15.200 |
379 | Hub of the KPZ | 4062.10.795 |
380 | Leading half coupling | 4020.06.06-4 |
381 | Hub seal for gearbox-ZD ø115mm | |
382 | Gearbox hub hub seal ø135mm | |
383 | Hub seal for gearbox-ZD ø140mm | |
384 | Seal of reduction gear 1.2x105x38-3 | GOST 6678-72 |
385 | Faceplate | 4062.38.303 |
Blowout preventer (BOP) (lot is indivisible) | ||
386 | Blowout preventer equipment 13 5/8” x 10000 PSI, with annular preventer 13 5/8” x 5000 PSI PSI, the set includes: double ram preventer 13 5/8” x 10000 PS with pipe rams 5”, 1-annular preventer 13 5/8” x 5000 PSI, killing and choke manifold, discharge line with connecting flanges – 200 m, hydraulic control, rams Ø-5 “(127 mm) -4 pcs, Ø-5 1/2″ (140 mm) -4 pcs; blind -2 pcs, Ø-6 5/8″ (168 mm) -2 pcs; Ø-9 5/8″ (245 mm) -2 pcs; annular preventer element -2 pcs; adapter flange 13 5/8″ x 10000 PSI -13 5/8″ x 5000 PSI -1 pc; adapter flange 13 5/8″ x 10000 PSI -11” x 10000 PSI-1 pc; for servicing spare parts. | |
387 | Manifold throttling block 80×350 (China) | |
388 | Manifold throttling block 80×700 (China) | |
389 | Manifold muffler block 80×350 (China) | |
390 | Manifold muffler block 80×700 (China) | |
391 | Adapter flange 13.5/8-5000 PSI x 13.5/8-10000 PSI with studs, nuts and sealing rings | |
392 | Adapter flange 11″-10000 PSI x 13.5/8-10000 PSI with studs, nuts and sealing rings | |
393 | Test pump manual, hydraulic PSH-11 7 mPa (China) | 0534-2618906 (2616805) |
Spare parts for air defense equipment (2015) China | ||
394 | Crosspiece | FS350-70 mPa |
395 | Double ram preventer | 2FZ350x70 mPa |
396 | Universal preventer | FH-350/35 MPa |
397 | Adapter coil, height 700 mm 13 5/8×70 mPa x13 5/8×70 mPa | |
398 | Adapter 13 5/8×35 mPa X 13 5/8×70 mPa | |
399 | Adapter 11-70mPa X 13 5/8×70 mPa | |
400 | Pipe dies 127 mm | FZ350x70 mPa |
401 | Pipe dies 140 mm | FZ350x70 mPa |
402 | Pipe dies 168 mm | FZ350x70 mPa |
403 | Spherical rubber rod | F35.11.00 |
404 | Small O-ring for back-up ring | F751A.13.03 |
405 | Large O-ring for support ring | F35.13 |
406 | Sealing ring for support ring | F35.14.00 |
407 | Wear ring for support ring | F35.12.02 |
408 | Sealing ring for housing | F35.16.00 |
409 | Sealing ring for piston | F35.19.00 |
410 | Wear-resistant ring for piston | F35.20.02 |
Spare parts for preventer 2FZ-350×350 (PPG) (lot indivisible) | ||
411 | Set of dies ø127 | FZ 897.21.06.00 |
412 | Set of dies ø140 | FZ 897.21.07.00 |
413 | Upper plate seal | FZ 897.21.01.01 |
414 | Mechanical seal ø127 | RS 11148.09.04.02 |
415 | Mechanical seal ø140 | RS 11148.09.05.02 |
416 | Side door sealing ring | FZ 897.1.03B |
417 | Sealing ring “0” 230×5.9 mm | FZ 897.22 |
418 | Piston sealing ring | FZ 897.1.8 |
419 | Die shaft seal | GB 12.35-76 |
420 | Locking shaft seal | F 751.14.20 |
421 | Sealing ring “O” 110×5.7 mm | GB 12.35-76 |
Spare parts for the preventer FH-350×350 (PUG) (indivisible lot) | ||
422 | Ball rubber core | F35.11 |
423 | Sealing ring “O” of the inner support ring | F 751A. 13.03 |
424 | Sealing ring “O” outside of the support ring | F 35.13 |
425 | Sealing ring for support ring | F 35.14 |
426 | Wear ring for support ring | F 35.15 |
427 | Wear-resistant ring for the housing | F 35.17 |
428 | Wear-resistant ring for piston | F 35.18 |
429 | Piston sealing ring | F 35.19 |
Spare parts for preventer 2FZ-350×350 (PPG) (lot indivisible) | ||
430 | Set of dies ø127 | |
431 | Set of dies ø140 | |
432 | Upper plate seal | |
433 | Mechanical seal ø127 | |
434 | Mechanical seal ø140 | |
435 | Side door sealing ring | |
Spare parts for the preventer FH-350x350D (PUG) (indivisible lot) | ||
436 | Ball rubber core | |
437 | Sealing ring “O” of the inner support ring | |
438 | Sealing ring “O” outside of the support ring | |
439 | Sealing ring for support ring | |
440 | Wear ring for support ring | |
441 | Wear-resistant ring for the housing | |
Spare parts for preventer 13⅝”x70 UZD 02 “UZTEL” (Romania) (indivisible lot) | ||
442 | Die Block 6⅝” (168 mm) | 305100050437 |
443 | Die Block 5½” (140 mm) | 305100043366 |
444 | Die block 5″ (127 mm) | 305100048778 |
445 | Blowout Preventer Piston Rod 11×35 | 305100049677 |
446 | Replacement bushing ø90 mm | 305100027143 |
447 | Replacement bushing ø120 mm | 305100048624 |
448 | Lid sealing gasket | 305100043421 |
449 | Sealing gasket ø70 | 450030300002 |
450 | Sealing gasket for rod ø90 | 716014511002 |
451 | Sealing gasket for rod ø120 | 716014623004 |
452 | Ring “0”-53007100 | 714101157005 |
453 | Ring “0”-53009000 | 714101165008 |
454 | Ring “0”-70012200 | 714101596008 |
Spare parts for preventer 13⅝”x70 UZ 03 “UZTEL” (Romania) (lot indivisible) | ||
455 | Ring die | 305100048079 |
456 | Sealing bag 683 | 716001329003 |
457 | Sealing bag 646 | 716001332004 |
458 | Sealing bag 746 | 716001335007 |
Spare parts for air defense manifold “UZTEL” (Romania) (lot indivisible) | ||
459 | Adjustable nipple | Series 924 |
460 | Wedge gate valve with threaded end | Series 810, 811 |
461 | Wedge gate valve with flanged end | Series 810, 811 |
462 | Wedge gate valve with flanged end | Series 813 |
463 | Hydraulically operated gate valve | HM 810, 811 Series |
464 | Gate valve with hydraulic-manual drive | HM 810, 811 Series |
Spare parts for the PPG preventer 16¾”x21 “UPETROM” (Romania) (indivisible lot) | ||
465 | Die Block 5½” (140 mm) | |
466 | Die block 5″ (127 mm) | |
467 | Upper seal | |
468 | End seal die ø127 mm | |
469 | End seal die ø140 mm | |
470 | Door seal | |
Spare parts for the PUG preventer 16¾”x21 “UPETROM” (Romania) (indivisible lot) | ||
471 | Sealing cuff | |
472 | Ring element | |
Steel rope | ||
473 | Steel rope ø12 mm | |
474 | Steel rope ø15 mm | |
475 | Steel rope ø16.5 mm | |
476 | Steel rope ø19.5 mm | |
Pumps are different | ||
477 | Pump 32-PL for cooling rods, vertical with electric motor | 12VB.22.00B (F-1600/F-1300) |
478 | Centrifugal 32-B180J- 2.2 kW(50Hz) spray pump, without electric motor | BZ030100 |
479 | Centrifugal pump, top-up 11 kW, without electric motor | SB4″x3″-9.5″ |
480 | Centrifugal pump for funnel 75 kW, without electric motor | SB8x6х12-1/2″ |
481 | Centrifugal pump 55 kW without electric motor | SB8x6J-12-12,5″ |
482 | Cutting pump 55 kW, without electric motor | JQ6x5J-10 |
483 | Booster pump 55 kW, without electric motor | SB8x6x12 |
484 | Gear pump 2S | NB060300 |
485 | Gear oil pump LWBZ-40/6 (50HZ) | BZ040100 |
486 | Sand pump SB-5″x60-12½″ without electric motor | SB568100 |
487 | Sand pump SB-2″x2J-8″; SB-2‴х3J-8‴ (80 m3/hour) without electric motor | SB230100 |
488 | Slurry pump SB-5‴х6J-12½‴ (155 m3/hour) without electric motor | SB 560100 |
Spare parts for drilling winch LBU-1200 or similar(lot is indivisible) | ||
489 | Lifting shaft | 4062.78.150 |
490 | 5th speed transmission shaft | 4062.79.000 |
491 | Rotor transmission | 4062.92.000 |
492 | Spool friction shaft | 4062.80.000 |
493 | Spool shaft | 4062.92.00 |
494 | Friction reel | 4062.80.100 |
495 | Winch gearbox shaft I | 4062.91.151 |
496 | Winch gearbox shaft II | 4062.99.104 |
497 | Winch gearbox RL-11000 | 4062.99.150 |
498 | Brake pulley | 4062.78.136 |
499 | Cardan shaft with hook (L=2680 mm)01.052.200-03 | 4062.90.600 Sat |
500 | Glass of GUKs | |
501 | Cardan shaft crosspiece splined | 4062.90.517 |
502 | Cardan shaft crosspiece keyed | 4062.90.518 |
503 | Double swivel, 2-cantilever | 4062.39.100 |
504 | Swivel 4-10 03.2067.002 | 4062.97.200 |
505 | Flanged swivel 2-16 (single) | 03.2067.002 |
506 | 2-valve tap | 4008.71.500-2 |
507 | 4-valve tap | 4003.71.220-10 |
508 | 4 valve valve | 4008.71.243 |
509 | Surge arrester valve | 4062.71.070 |
510 | Distributor REP 1-1-20 1.0 MPa | 14088.95.250-01 |
511 | Friction reel pulley | 4062.80.121 |
512 | Drag reel brake | 4062.84.200 |
513 | Friction reel tape | 4062.84.201sb |
514 | Friction reel lining | 4066.43.127 |
515 | Brake band | 4062.81.000 |
516 | Rotor transmission cam clutch | 4062.92.008 |
517 | Driller’s control panel | 4062.95.050 |
518 | Hydrodynamic brake unit UTG-1450 | 4062.76.100 |
519 | Hydrodynamic brake tank UTG-1450+A566 | 4062.97.160 |
520 | Pneumatic fastener | 4062.85.000 |
521 | Chain Puller | 4085.08.450 |
522 | Roller guide insert assembly | 4062.45.450 Sat. |
523 | Cardan rubber or similar | |
Tyre-pneumatic coupling or similar (lot indivisible) | ||
524 | Tyre pneumatic coupling 300×100 | |
525 | Tyre pneumatic coupling 500×125 | |
526 | Tyre pneumatic coupling 700×200 | |
527 | Tyre pneumatic coupling 1070×200 | |
Spare parts for drilling pump UNB-600 or similar (lot indivisible) | ||
528 | Hydraulic box (left) | 4045.53.811 |
529 | Hydraulic box (right) | 4045.53.812 |
530 | Cylinder bushing ø130 mm | 4045.53.501-07 |
531 | Cylinder bushing ø140 mm | 4045.53.501-06 |
532 | Cylinder bushing ø150 mm | 4045.53.501-05 |
533 | Cylinder bushing ø160 mm | 4045.53.501-04 |
534 | Cylinder bushing ø170 mm | 4045.53.501-03 |
535 | Cylinder bushing ø180 mm | 4045.53.501-02 |
536 | Cylinder bushing ø200 mm | 4066.53.501 |
537 | Piston ø130 mm | 4045.53.230 |
538 | Piston ø140 mm | 4045.53.233 |
539 | Piston ø150 mm | |
540 | Piston ø160 mm | 4045.53.235 |
541 | Piston ø170 mm | |
542 | Piston ø180 mm | 4045.53.237 |
543 | Piston ø200 mm | 4045.53.239 |
544 | Bronze bushing | 4045.53.66-1 |
545 | Piston rod ШП-70 with nuts | 4066.53.520-SB |
546 | Rod seal M-70 | 4066.53.53 |
547 | Rod seal housing | |
548 | Valve cover cuff | 4066.53.212 |
549 | K-9 valve assembly | 14023.53.090-2 |
550 | Cylinder liner seal | 4066.53.578 |
551 | Cylinder liner ring | 4066.53.586 |
552 | Valve plate | 4066.53.615 |
553 | Compensator diaphragm D-70 | 4045.53.230 |
554 | Crosshead pin | 4045.53.76-2 |
555 | Cylinder cover with bolts | 4045.53.259-3 |
556 | Valve cover | 4045.53.259-3 |
557 | Piston lock nut | 4045,53,511-1 |
558 | Crosshead guide (lower) | 4045.53.105.4 |
559 | Crosshead guide (upper) | 4045.53.106.4 |
560 | Membrane with a set of rings | 4066.53.271 4066.53.753 |
561 | Valve body of the box with nut | |
562 | Studs M42x200 with nuts | |
563 | Spacer ring | |
564 | Glass assembly (cylinder boxes) | |
565 | Crosshead lining (slider) | |
Spare parts for compressor “4VU 1-5/9M4UHL4” or analogue (lot indivisible) | ||
566 | Crankshaft with bearing 302601033N | 302-601-03 3P 1 |
567 | I-stage piston assembly | 302-601-06-3/03-24 |
568 | II stage piston assembly | 302-601-06-3/03-25 |
569 | 1st stage cylinder block | |
570 | 2nd stage cylinder block | |
571 | Countershaft for mechanical compressor | 4062.70.050 |
572 | Piston ring, compression U-125 in assembly | 302-601-06-3/04-34 |
573 | Piston ring, oil scraper MP-125 in assembly | 31680/04-132 |
574 | Piston ring, compression U-210 in assembly | 302-601-06-3/04-31 |
575 | Piston ring, oil scraper MP-210 in assembly | 31677/04-130 |
576 | Retaining ring | |
577 | Connecting rod assembly | 302-601-04 A |
578 | Air swivel (left) for counter drive | 26007.3040.16 |
579 | 2nd stage valve head | |
580 | Piston pin | |
581 | 1st stage saddle | |
582 | 1st stage plate | |
583 | 2nd stage saddle | |
584 | 2nd stage plate | |
Spare parts for step-down gearbox JS-1200 (China) (lot indivisible) | ||
585 | I-st shaft of the power reducer with bearings | |
586 | II-nd shaft of the power reducer with bearings | |
587 | Step-down gearbox (1.53)(900 kW)(1500 rpm) (1275x1085x980) | JS-1200 |
588 | Cardan clutch assembly | W51.5×870 |
Spare parts for rotor R-700 or analogue (lot indivisible) | ||
589 | Drive shaft of the rotor R-700 | 14016.45.010 |
590 | Roller guide insert | 4062.45.450 |
591 | Rotor insert R-700 | 1416.45.270 |
592 | Rotor jaw R-560 | 4-8-41/82 |
593 | Star Z=19 P=50.8 | 4045.45.520 |
594 | Asterisk Z=21 P=50.8 | 4045.45.511 |
595 | Asterisk Z=23 P=50.8 | 4045.45.512 |
596 | Bevel gear Z-18 | 14016.45.015 |
597 | Cord 4s ø8 mm. L=3.0 M. | |
598 | Cord 4s ø5 mm. L=6.0 M. | |
599 | Seal 210 | |
600 | Main support (bearing 1687/770) | |
601 | Auxiliary support (bearing 1688/770) | |
Spare parts for manifold “MV-2U” or similar | ||
602 | Manifold gate valve ZPRM-100×400 | 00.00.000 |
603 | Manifold valve ZPRM-100×320 | 00.00.000 |
604 | Manifold gate valve ЗМ-80х35G (hydraulic) | M10.02.02.000 |
Spare parts for crane KP | ||
605 | Crane rotation reducer with electric motor KPB-3M or similar | 01.00.000.SAT |
Lifting equipment | ||
606 | Electric hoist 10 tons, height 8 meters | GOST22584-96 |
607 | Electric hoist 5 tons, height 6 meters | |
608 | Electric hoist 3.2 tons, height 6 meters | |
609 | Electric hoist 2 t, 6m high | |
610 | Hand hoist 1.5 t, 6 m high | |
Spare parts for hydraulic station CH6U-76«UPETROM» (Romania) | ||
611 | Triple plunger pump 3RU-20 | 614.20-00.00.00.0 |
Electric gas welding equipment, tools and accessories | ||
612 | Welding unit on chassis | |
613 | Welding transformer ВХ1-400 (China) | JB 3643-2000 |
614 | Welding unit without chassis | |
615 | Electrode “ANO” ø4 mm | |
616 | Electrode “UONI” ø4 mm | GOST9466-75 |
617 | Electrode “UONI” ø3 mm | |
618 | Manual cutting cutter RZP-902 or similar | RSR-106R |
619 | Propane reducer BPO 5-4 or similar | RED-907 |
620 | Oxygen reducer BKO 504 or similar | RED-905 |
621 | Oxygen cylinder valve VK-74 or similar | |
Rolling bearings (lot indivisible) | ||
622 | Bearing 205 | GOST 7242-81 |
623 | Bearing 207 | GOST 8338-75 |
624 | Bearing 208 | GOST 8338-75 |
625 | Bearing 209 | GOST 8338-75 |
626 | Bearing 210 | GOST 8338-75 |
627 | Shaft bearing 214 | GOST 8338-75 |
628 | Shaft bearing 302 | GOST 8338-75 |
629 | Shaft bearing 305 | GOST 8338-75 |
630 | Shaft bearing 309 | GOST 8338-75 |
631 | Bearing 310 | GOST 8338-75 |
632 | Bearing 311 | GOST 8338-75 |
633 | Bearing 312 | GOST 8338-75 |
634 | Bearing 313 | GOST 8338-75 |
635 | Bearing 314 | |
636 | Bearing 317 | |
637 | Bearing 322 | |
638 | Bearing 1612 | GOST 5721-75 |
639 | Bearing 2236 | |
640 | Bearing 2322 | |
641 | Bearing 3518 (22218) | GOST 5721-75 |
642 | Bearing 3519 (22219) | GOST 5721-75 |
643 | Bearing 3520 (22220) | GOST153520 |
644 | Bearing 3522 (22222) | GOST 5721-75 |
645 | Bearing 3524 (22224) | GOST 5721-75 |
646 | Bearing 3528 (22228) | GOST 520-2011 |
647 | Bearing 3538 (22238) | GOST 8338-75 |
648 | Bearing 3530 (22230) | |
649 | Bearing 3612 (22312) | GOST 8338-75 |
650 | Bearing 3618 (22318) | GOST 5721-75 |
651 | Bearing 3622 (22322) | GOST 8338-75 |
652 | Bearing 3624 (22324) | GOST 8338-75 |
653 | Bearing 3628 (22328) | GOST 8338-75 |
654 | Bearing 3630 (22330) | GOST 8338-75 |
655 | Bearing 3634 (22334) | GOST 5721-75 |
656 | Bearing 3636 (22336) | GOST 5721-75 |
657 | Bearing 5692/800 | GOST31309-98 |
658 | Bearing 5691/800 | GOST31309-99 |
659 | Bearing 6228 | GOST 7372-89 |
660 | Bearing 6311 | GOST 7372-89 |
661 | Bearing 7352 | GOST 333-79 |
662 | Bearing 7538 | GOST7372-89 |
663 | Bearing 51111 | GOST6874-75 |
664 | Bearing 10079/710 | GOST520-2011 |
665 | Bearing 8110 | |
666 | Bearing 8222 | |
667 | Bearing 32617 | |
668 | Bearing 24122 | GOST4053722 |
669 | Bearing 32630 | ZP050018 |
High pressure hoses (lot indivisible) | ||
670 | Rubber sleeve ø9 mm 2.0 mPa oxygen | GOST9356-75 |
671 | Rubber sleeve ø15 mm 2.0 mPa | GOST 18698-79 |
672 | Rubber sleeve ø20 mm 2.0 mPa | GOST 18698-79 |
673 | Rubber sleeve ø25 mm 2.0 mPa | |
674 | Rubber sleeve ø32 mm 2.0 mPa | |
675 | Rubber sleeve ø42 mm 2.0 mPa | |
Sealing materials (lot is indivisible) | ||
676 | Gland packing ø 8mm | 8x8mm |
677 | Gland packing ø10 mm | 10x10mm |
678 | Gland packing ø12 mm | 12x12mm |
679 | Gland packing ø15 mm | 15x15mm |
680 | Gland packing ø22 mm | 22x22mm |
681 | Impregnated hemp gland packing | 14 x 14 mm |
682 | Impregnated hemp gland packing | 16 x16 mm |
683 | Impregnated hemp gland packing | 18 x 18 mm |
684 | Impregnated hemp gland packing | 19 x 19 mm |
685 | Oil and petrol resistant paronite | PMB-1 mm |
686 | Oil and petrol resistant paronite | PMB-2 mm |
687 | Oil and petrol resistant paronite | PMB-3 mm |
688 | Oil and petrol resistant paronite | PMB-4 mm |
689 | FUM tape 0.1-1.0 | 92480800011 |
690 | FUM tape 0.08-1.5 | 92480800011 |
Belts (lot indivisible) | ||
691 | Belt A-1250 mm | GOST 1284.1-89 |
692 | Belt B-1250 mm | |
693 | Belt A-1330 mm | |
694 | Belt B-1400 mm | |
695 | Belt B-1650 mm | |
696 | Belt B-1600 mm | |
697 | Belt B-1800 mm | |
698 | Belt A-2000 mm | |
699 | Belt B-2000 mm | |
700 | Belt A-2120 mm | |
701 | Belt A-2240 mm | |
702 | Belt A-2800 mm | GOST 1284-80 |
703 | Belt C-4000 mm | GOST 1284.1-89 |
704 | Belt C(B)-4500 mm | GOST 1284.1-89 |
705 | Belt E(D)-5600 mm | GOST 1284.1-89 |
706 | Belt E(D)-10000 mm | GOST 1284.1-89 |
Wellhead equipment | ||
707 | Column head complete with fountain fittings OKK-3-70 MPa 140x245x324x426 with AFC 6-80/65×70 MPaWELL HEAD CASING SIZES 16.3/4″ x 12.3/4″ x 9.5/8″ x 5.1/2″ x 10000 PSI AND X-MAS TREE ASSEMBLY 3.1/16″ x 2.9/16″ x 10000 PSI | |
708 | Column head complete with fountain fittings OKK-3-70 MPa 168x245x340x508 with AFC 6-80/65×70 MPa WELL HEAD CASING SIZES 20″ x 13.3/8″ x 9.5/8″ x 6.5/8″ x 10000 PSI AND X-MAS TREE ASSEMBLY 3.1/16″ x 2.9/16″ x 10000 PSI | |
709 | Column head complete with fountain fittings OKK-2-70 MPa-140x245x324 with AFK6-80/65×70 MPaWELL HEAD CASING SIZES 12.3/4″ x 9.5/8″ x 5.1/2″ x 10000 PSI AND X-MAS TREE ASSEMBLY 3.1/16″ x 2.9/16″ x10000 PSI | |
710 | Column head complete with fountain fittings OKK-2-70 MPa 140x245x340 with AFK6-80/65×70 MPa WELL HEAD CASING SIZES 13.3/8″ x 9.5/8″ x 5.1/2″ x 10000 PSI AND X-MAS TREE ASSEMBLY 3.1/16″x2.9/16″ x10000 PSI | |
711 | Column head complete with fountain fittings OKK-2-35 MPa-140x245x324 with AFK6-65×35 MPa WELL HEAD CASING SIZES 12.3/4″ x 9.5/8″ x 5.1/2″ x 5000 PSI AND X-MAS TREE ASSEMBLY 3.1/16″ x2.9/16″ x 5000 PSI | |
712 | Column head complete with fountain fittings OKK-2-35 MPa-168x245x340 with AFK6-65×35 MPaWELL HEAD CASING SIZES 13.3/8″ x 9.5/8″ x 6.5/8″ x 5000 PSI AND X-MAS TREE ASSEMBLY 3.1/16″ x2.9/16″ x 5000 PSI | |
713 | Column head complete with fountain fittings OKK-1×35 mPa-140×245 with AFK6-65×35 mPa WELL HEAD CASING SIZES 9.5/8″ x 5.1/2″ x 5000 PSI AND X-MAS TREE ASSEMBLY 3.1/16″ x2.9/16″ x 5000 PSI | |
Spare parts for wellhead equipment (lot indivisible) | ||
714 | Wedge packer 16¾” x 12¾”-10000 PSI with top sealing cuff “R24” API | KYD 80-700 |
715 | Wedge Packer 13⅝” x 9⅝”-10000 PSI with API “R24” Upper Seal | KYD 80-700 |
716 | Wedge Packer 11″ x 5½”-10000 PSI with API “R24” Upper Seal | KYD 80-700 |
717 | Wedge Packer 9″ x 5½”-10000 PSI with API “R24” Upper Seal | KYD 80-700 |
718 | Sealing Gasket BX156 API | |
719 | Sealing Gasket BX153 API | |
Spare parts for diesel engine CAT-3512, CAT-3512B (lot indivisible) | ||
720 | Oil filter (manufactured by CAT) | 1R-0726 |
721 | Fuel filter (manufactured by CAT) | 1R-0756 |
722 | Air filter (manufactured by CAT) | 4P-0710 |
723 | Air filter (manufactured by CAT) | 4P-0711 |
724 | Air filter (manufactured by CAT) | 8N6309 |
725 | Air filter (manufactured by CAT) | 8N2556 |
726 | Fan belt (6 V-belts) | 8N6700 |
727 | Fan blade assembly | |
728 | Main water pump | 2W-9729 |
729 | Pneumatic starter | INGERSOL(2015) |
730 | Water cooling radiator core with seal | 3215B (RTM) |
731 | Radiator core with sealing cuff | 3512 (RTN) 2W-0181 |
Spare parts for diesel engine CAT C-15 (lot indivisible) | ||
732 | Air compressor “CAT” (256-6164) | 223-3637 |
733 | Oil filter (manufactured by CAT) | 1R0716 |
734 | Fuel filter (manufactured by CAT) | 1R0749 |
735 | Vee Belt-Fan | Vee Belt Fan |
736 | Air filter | 1890202 |
737 | Air filter | 9Y3879 |
738 | Water radiator “SAT” (256-6164) | 256-2674 |
739 | Water pump “CAT” (174-5986) | 161-5719 |
740 | Fuel supply pump “CAT” (2574-7275) | 191-5054 |
741 | Turbocharger “CAT” (239-9988) | 242-3492 |
742 | Electric starter 24V “CAT” (120-9100) | 237-1962 |
743 | Generator 28V “CAT” (317-3821) | 332-4696 |
744 | Fan Drive Belt “CAT” (197-4567) | 5N-2346 |
745 | Alternator Belt “CAT” (286-8179) | 7N-3949 |
Spare parts for diesel engine CAT-3508 (lot indivisible) | ||
746 | Water radiator “CAT” (7E-7528) (PTN) (core) | 7C-4401 |
747 | Pneumatic starter «CAT» (7С-3371) INGERSOL (2010) | 7C-3372 |
748 | Fan drive belt | HG/T-2819 |
749 | Fuel pump “SAT” (8N-6151) | 169-8615 |
Spare parts for diesel engine CAT-3406, CAT-3408 (lot indivisible) | ||
750 | Generator 24V “CAT” (5N-5692) | CAT-3406 JDK |
751 | Electric starter 24V (5N-4801) | CAT-3406 JDK |
752 | Oil filter (manufactured by CAT) | 1R-0716 |
753 | Fuel filter (manufactured by CAT) | 1R-0749 |
754 | Water radiator “CAT” (142-3318) | 142-1928 |
755 | Oil pump “CAT” | 161-4113 |
756 | Water pump “CAT” (9N-3288) | 135-4926 |
757 | Fuel pump “CAT” (2W-8543) | 4P-1385 |
758 | Turbocharger “CAT” (1W-4209) | 1W-3728 |
759 | Drive belt “CAT” (7N-8840) | 6N-6656 |
760 | Drive belt “CAT” (7 W-1340) | 4N-8216 |
Pumping equipment for the management of “Water supply” | ||
761 | CNS 300×300 with electric motor 400 kW 1500 rpm not explosion-proof or similar | CNS 300×300 |
762 | CNS 300×240 with electric motor 315 kW 1500 rpm not explosion-proof or similar | CNS 300×240 |
763 | CNS 300×180 with electric motor 315 kW 1500 rpm not explosion-proof or similar | CNS 300×180 |
764 | CNS 180×255 with electric motor 250 kW 1500 rpm not explosion-proof or similar | CNS 180×255 |
765 | CNS 180×170 with electric motor 200 kW (6 kW) 1500 rpm not explosion-proof or similar | CNS 180×170 |
766 | CNS 180×128 with electric motor 132 kW 1500 rpm not explosion-proof or similar | CNS 180×128 |
767 | CNS 180×85 with electric motor 75 kW 1500 rpm not explosion-proof or similar | CNS 180×85 |
768 | CNS 850×240 with an electric motor 800 kW 1500 rpm not explosion-proof or similar | CNS 850×240 |
769 | Pump D 200/36 with electric motor 45 kW 1500 rpm not explosion-proof or similar | D 200/36 |
770 | Pump OMEGA 250-800A or similar | |
771 | Pump K40x40 or similar | |
Spare parts for the pump CNS 850 (lot indivisible) | ||
772 | CNS-850 Shaft | |
773 | CNS-850 Impeller 1 stage | MSG-7-01-118-1 |
774 | CNS-850 Impeller | MSG-7-01-178 |
775 | CNS-850 Distance bushing | MSG-7-01-126-1 |
776 | CNS-850 Water seal bushing | MSG-7-01-112 |
777 | CNS-850 Guide apparatus | MSG-7-01-119 |
778 | CNS-850 Protective bushing | |
779 | CNS-850 Bearing bushing | |
780 | CNS-850 1st stage guide vane | |
781 | TsNS-850 Bushing 190312 | MSG-7-01-102,00 |
782 | CNS-850 Nut 1904 | MSG-7-01-107 |
783 | TsNS-850 Bushing oil seal 1905 | MSG-7-01-108 |
784 | CNS-850 Shaft shirt 1906 | MSG-7-01-109,1 |
785 | CNS-850 Front bracket | MSG-7-01-114 |
786 | CNS-850 Suction cover 1909 | MSG-7-01-116 |
787 | CNS-850 Sealing ring 1st stage 1910 | MSG-7-01-117 |
788 | CNS-850 Working wheel 2nd stage 191112 | MSG-8-01-118-1 |
789 | CNS-850 Sealing ring 1913 | MSG-7-01-121 |
790 | CNS-850 Sealing ring 1914 | MSG-7-01-122 |
791 | CNS-850 Device for guiding when issuing 1915 | MSG-7-01-123 |
792 | CNS-850 Unloading Bushing 1916 | MSG-7-01-125-1 |
793 | CNS-850 Discharge cover 1918 | MSG-7-01-132-1 |
794 | CNS-850 Rear bracket 1919 | MSG-7-01-135-1 |
795 | CNS-850 Rotary Nut 1924 12 | MSG-7-01-142-1 |
796 | CNS-850-240 Shaft (2 stage) | |
Spare parts for the CNS 300 pump (lot indivisible) | ||
797 | CNS-300 Rotor Nut | 8MS 7.01.07 |
798 | Body of the device guiding CNS 300-120-600 | 8MS 7.0119-2 |
799 | CNS-300 Guide ring | CNS 300-120 |
800 | CNS-300 Sealing cord for the guide apparatus housing | CNS 300-120 |
801 | CNS-300 Working wheel when issuing | 8MS 7.0118-1 |
802 | CNS-300 Sealing ring | 8MS 7.0120 |
803 | CNS-300 Sealing ring | 8MS 7.0121 |
804 | CNS-300 Unloading disk | 8MS 7.0109 |
805 | CNS-300 Shaft of 3-stage pump | CNS300-180 |
806 | CNS-300 Bearing bushing | |
807 | CNS-300 Cuff | GOST 87-52-79 |
808 | CNS-300 Throttling bushing | |
809 | CNS-300 working wheel | 8MS 7.0118 |
810 | CNS-300 impeller 1 stage | |
811 | CNS-300 shaft shirt | 8MS 7.0126 |
812 | CNS-300 Distance bushing | 8MS 7.0113 |
813 | CNS-300 Water seal bushing | CNSN-300-180.001 |
814 | CNS-300 Front bracket | 8MS 7.0129 |
815 | CNS-300 Rear bracket | 8MS 7.0103 |
816 | CNS-300 Unloading bushing | 8MS 7.0114 |
817 | CNS-300 Unloading ring | 8MS 7.0112 |
818 | CNS-300 Unloading ring | 8MS 7.0111 |
819 | CNS-300 Guide apparatus | 8MS 7.01.17-1 |
Spare parts for the pump CNS 180 (lot indivisible) | ||
820 | CNS-180 Impeller I-stage | 180 x 255 |
821 | CNS-180 Shaft shirt | CNS 180-255.001 |
822 | CNS-180 Distance bushing | 6MS 6-0113 |
823 | CNS-180 Water seal bushing | 6MS 6-0126 |
824 | CNS-180 Unloading bushing | 6MS 6-0114 |
825 | CNS-180 Unloading ring | CNS 180-255 6 MS-0119 |
826 | CNS-180 Guide apparatus | 6MS 6-0117-1 |
827 | CNS-180 Throttling bushing | |
828 | CNS-180 Front bracket | |
829 | CNS-180 Rear bracket | |
830 | CNS-180 Bearing bushing | |
831 | CNS-180 Cuff | GOST 87-52-79 |
832 | CNS-180 Sealing ring | 6 MS 6-0121 |
833 | CNS-180 Sealing ring | 6 MS 6-0122-1-02 |
834 | CNS-180 Working wheel | 6 MS 6-0118 |
835 | CNS-180 Body of the guide apparatus | 6 MS 6-01.129 |
836 | CNS-180 Guide ring | CNS 180×85 85.1.425.01.009 |
837 | TsNS-180 Shaft of 3-stage pump | CNS 180×128 |
838 | CNS-180 5-stage pump shaft | CNS 180×212 |
Needs of the Repair and Mechanical Plant (RMZ) | ||
Spare parts for pumps CNS-300÷120÷600 (lot indivisible) | ||
839 | Support bracket | GOST R54804-2011 |
840 | Suction cover rear | |
841 | Rear support bracket | |
842 | Pressure cover rear | |
843 | Impeller | |
844 | Guide apparatus | |
845 | Guide vane section | |
846 | Shaft shirt | |
847 | Spacer sleeve | |
848 | Unloading disk | |
849 | Unloading ring | |
850 | Rotary nut | |
Spare parts for pumps CNS-180÷85÷425 (lot indivisible) | ||
851 | Support bracket | GOST R54804-2011 |
852 | Suction cover front | |
853 | Rear support bracket | |
854 | Pressure cover rear | |
855 | Impeller | |
856 | Guide apparatus | |
857 | Guide vane section | |
858 | Shaft shirt | |
859 | Spacer sleeve | |
860 | Unloading disk | |
861 | Unloading ring | |
862 | Rotary nut | |
Spare parts for cementing unit (lot indivisible) | ||
863 | Plug valve d=50 P=70 (Pump SIN 64.00.100.000) | 2KMN |
864 | Articulated elbow d=50 P=70 (Pump SIN 64.00.100.000) | KS-70 |
865 | Plunger d=100-7-72 (Pump SIN 64.00.100.000) | |
866 | Valve SP-507 tripleks pump 5S with proportional cover (Pump SP-507) | SP-507 tripleks |
867 | Valve seat SP-507 triplex pump | |
868 | Inlet hose d=100 L=4.5 (Pump NSP-32) | SIN 30.01.0700000 |
869 | Inlet hose d=75 L=3m (Pump NSP-32) | |
870 | High pressure hose P=35, L=10 (d=50)(Pump NSP-32) | |
871 | Discharge hose P=7, L=10 (d=50) (Pump NSP-32) | |
872 | Adjustable nozzle 2×1050 | |
873 | Articulated elbow 22 type R2”x1050 Bar (Pump SIN 64.00.100.000) | |
874 | Plug valve 2x2nkt 60 P=105 MPa (Pump SIN 64.00.100.000) | GOST 633-80 |
875 | Plug valve 2x1nkt 60 P=105 MPa (Pump SIN 64.00.100.000) | GOST 633-80 |
876 | Plug valve 2x1nkt 60 P=105 MPa | GOST 633-80 |
877 | Valve d=111 mm 9T.2.69 (Pump NPS-32) | 9T.2.69 |
878 | Valve seat d=111T.118A (NPS-32 pump) | T.118A |
879 | Cylinder sleeve d=100 (Pump NPS-32) | 6G-102 |
880 | Cylinder sleeve d=127 (Pump NPS-32) | 6G-104 |
881 | Gear pump NS-10 (Pump NPS-32) | |
882 | Gate valve d=100(4″) (Pump NPS-32) | SIN 100.13.000 |
883 | Worm NPS 01.029A (Pump NPS-32) | NPS 01.029A |
884 | Articulated knee KS-40 d=50 P=40 | KS-40(NPS-32) |
885 | Piston D=127 mm (Pump NPS-32) | 9T.2.34 |
886 | Cylinder sleeve D=115 (Pump NPS-32) | 6G-103 |
887 | Crosshead assembly (NPS-32 pump) | 9G.01.200 |
888 | Plunger d=85mm. | |
889 | Plunger d=125mm. | |
890 | Cuff 125x145mm. | |
891 | Plunger cuff Ø100mm. | |
892 | Plunger cuff Ø85mm. | |
9. Procurement Guidance
This complete Turkmenistan drilling rig spare parts list covers all vulnerable and wearable components of core drilling, power, circulation and well control equipment, with stable quality, precise model matching and complete standard certification. We support accurate model verification, customized spare parts matching, and full provision of certification test documents and technical parameter data. For on-site equipment maintenance, spare parts stocking, and batch procurement demands, you can consult for professional technical selection guidance, confirm component adaptation and delivery specifications, and obtain targeted drilling rig spare parts supply solutions.