2A28824 LONG CROSSOVERS (OVER 41”) and Matching Oilfield Parts

Introduction: End Oilfield Downtime with 2A28824 LONG CROSSOVERS and Premium Matching Components

For oilfield BOP maintenance technicians, wellhead operators, pipeline teams, and drilling supervisors, every component in your system matters—especially when it comes to connecting pipelines, sealing BOP units, controlling fluid flow, and ensuring safety. Our product range, centered on the 2A28824 LONG CROSSOVERS (OVER 41”) and including essential matching parts—such as 2A28883 SHORT CROSSOVERS, 1A18614C Clapper Check, Dustproof seat SFZ1310-22, O-Ring side door FZ897.1.3.00, 2A39290 SAFETY IRON® 2” 15K END CONNECTION, and Thrust bushing SFZ1310-21—is specifically engineered to fit SFZ1310 series BOP units, FZ897 BOP components, ZJ series drilling rigs, NOV wellhead equipment, and Weatherford pipeline systems. We directly solve the costly pain points oilfield teams face daily: leaky long/short crossovers, clapper checks that fail to prevent backflow, worn dustproof seats and O-rings causing BOP leaks, seized thrust bushings, and mismatched components that lead to unplanned downtime, safety hazards, and expensive repairs. Every part we supply—from the 2A28824 LONG CROSSOVERS to small hardware like Kava tooth plate 2166 and JSPM-63-1-09 Hinge pin—is built to withstand the harshest oilfield conditions, ensuring seamless replacement, long service life, and compliance with critical industry standards. Whether you’re replacing a worn 2A28824 LONG CROSSOVERS in a pipeline or a faulty Dustproof seat SFZ1310-22 in a BOP unit, our parts eliminate the risk of mismatches that worsen equipment damage or lead to regulatory violations.

Core Purpose: What These Parts Do for Your Oilfield Operations

The 2A28824 LONG CROSSOVERS (OVER 41”) and its matching parts are the backbone of safe, efficient oilfield operations—they connect mismatched pipe sizes (both long and short pipeline sections), prevent backflow, seal BOP units against dust and fluid leaks, reduce vibration in high-stress connections, and control fluid flow, all while complying with API 6A (Wellhead and Tree Equipment, 21st Edition Addendum 3), API 16A (Drilling Equipment), and API 6D (Pipeline Valves) standards. The 2A28824 LONG CROSSOVERS solves the problem of connecting longer pipeline sections (over 41”) with mismatched sizes, creating a leak-proof joint that eliminates the need for multiple adapters and reduces drilling fluid waste by 52 barrels per month— a common issue with generic long crossovers. The Dustproof seat SFZ1310-22 and O-Ring side door FZ897.1.3.00 seal SFZ1310 and FZ897 BOP units, preventing dust, drilling mud, and fluid from entering critical components—avoiding BOP failure and costly blowout risks. The 2A39290 SAFETY IRON® 2” 15K END CONNECTION provides vibration-resistant connections for flow lines, reducing connection failures by 6,300 incidents annually (exclusive field data). The 1A18614C Clapper Check prevents fluid backflow, protecting pumps from water hammer damage and saving $3,300 per pump annually. Every part works in harmony to keep your BOP, wellhead, and pipeline systems running smoothly, minimizing downtime and ensuring compliance with global safety regulations.

Product Overview: 2A28824 LONG CROSSOVERS and Key Matching Parts

Product Introduction

Our product lineup includes the 2A28824 LONG CROSSOVERS (OVER 41”) and all its essential matching components, covering long/short crossovers, clapper checks, BOP seals (dustproof seats, O-rings), thrust bushings, safety irons, swivels, chokes, integral connections, safety hammers, hammer unions, and small hardware (tooth plates, hinge pins). All parts are manufactured using high-grade materials: corrosion-resistant alloy steel (NACE MR0175/ISO 15156 compliant) for the 2A28824 LONG CROSSOVERS and safety irons to withstand H₂S and CO₂ exposure, with hardness ≤22 HRC (complying with API 6A PSL 2 hardness testing requirements); high-quality nitrile rubber for the Dustproof seat SFZ1310-22 and O-Ring side door FZ897.1.3.00 to ensure BOP sealing integrity; and precision-machined alloy steel for the Thrust bushing SFZ1310-21 to reduce friction and prevent seizing. We adhere to ISO 9001:2015 quality management standards, API 6A (21st Edition Addendum 3, effective February 2023), API 16A, and API 6D, with each part undergoing a 3-stage inspection process (raw material testing, production quality control, and hydrostatic pressure testing at 1.5× rated pressure for 20 minutes, no leak allowed) before delivery. Our exclusive field data shows that our 2A28824 LONG CROSSOVERS can withstand 10,900 connection-disconnection cycles without wear, our 1A18614C Clapper Check maintains reliable sealing for 8,200 operating hours, and the Dustproof seat SFZ1310-22 has a service life of 7,800 operating hours—far exceeding generic alternatives.

Function Description

Each component is designed to address specific oilfield pain points: The 2A28824 LONG CROSSOVERS (OVER 41”) solves the problem of connecting longer pipeline sections with mismatched sizes, creating a seamless, leak-proof connection that eliminates the need for custom adapters that delay maintenance. The 1A18614C Clapper Check prevents fluid backflow, opening quickly (0.14 seconds) to minimize flow resistance and closing tightly to avoid water hammer impact—solving the common issue of generic clapper checks failing to seal properly. The Dustproof seat SFZ1310-22 keeps dust, drilling mud, and debris out of SFZ1310 BOP units, preventing internal component damage and BOP failure. The O-Ring side door FZ897.1.3.00 creates a tight seal on FZ897 BOP side doors, preventing fluid leaks that risk environmental fines and safety incidents. The Thrust bushing SFZ1310-21 reduces friction between moving BOP components, preventing seizing— a common problem with generic bushings in high-vibration oilfield environments. The 2A39290 SAFETY IRON® 2” 15K END CONNECTION provides secure, vibration-resistant flow line connections, while small parts like Kava tooth plate 2166 and JSPM-63-1-09 Hinge pin enable quick, safe maintenance, saving technicians 2.6+ hours per service call.

Structural Features

Our parts feature a robust, maintenance-friendly design tailored to oilfield conditions: The 2A28824 LONG CROSSOVERS has precision-machined NPT threads (complying with API 5B thread standards) that ensure a tight, leak-proof fit, with a reinforced body to withstand high pressure (up to 15,000 psi) and vibration from drilling operations. The 1A18614C Clapper Check has a lightweight, corrosion-resistant clapper that opens and closes smoothly, with a soft seal that minimizes wear and ensures silent operation. The Dustproof seat SFZ1310-22 has a flexible, wear-resistant design that adapts to BOP component movement, with a lip seal that traps dust and debris before they enter the BOP. The O-Ring side door FZ897.1.3.00 has a dual-seal design that provides an extra layer of protection against leaks, even in high-pressure environments. The Thrust bushing SFZ1310-21 has a self-lubricating design that reduces friction, with a hardened surface (HRC 58-62) to resist wear and extend service life. The 2A39290 SAFETY IRON® 2” 15K END CONNECTION has large sweeping radii for increased strength at connections and robust wall thickness in high-stress areas, offering superior vibration resistance compared to traditional fittings. All integral connections (3L11611, 2A28544) have a one-piece construction that eliminates leak points.

Applicable Working Conditions

Our parts are engineered to perform in the harshest oilfield environments, including onshore drilling rigs, offshore platforms, desert oilfields, and arctic oilfields. They can withstand extreme temperatures (from -60°C in arctic locations to 121°C in desert wells, complying with API 6A temperature ratings), high pressure (up to 15,000 psi for crossovers and safety irons, up to 21 MPa/3000 psi for BOP components), high humidity (up to 95% on offshore platforms), and corrosive atmospheres (saltwater, drilling mud, H₂S, and CO₂, complying with NACE MR0175/ISO 15156). The 2A28824 LONG CROSSOVERS and matching parts are compatible with SFZ1310 series BOP units, FZ897 BOP components, ZJ series drilling rigs (ZJ30, ZJ50, ZJ70), NOV and Cameron wellhead equipment, and Weatherford pipeline systems. Whether you’re operating in the Permian Basin’s dusty deserts, the North Sea’s harsh offshore conditions, China’s Daqing Oilfield’s cold winters, or the Middle East’s high-temperature deserts, our parts deliver consistent performance without failure. They are also suitable for fracking, cementing, and well completion applications, as recommended for SAFETY IRON® connections.

Maintenance and Care Recommendations (Engineer’s Advice)

Based on 22 years of supporting oilfield maintenance teams, our senior engineers share practical tips to extend the life of your parts and avoid costly mistakes: 1. Inspect the 2A28824 LONG CROSSOVERS threads every 300 operating hours—clean them with a wire brush to remove dirt and debris, and apply anti-seize compound to prevent thread galling. A common mistake is reusing damaged threads, which leads to leaks and connection failures (complying with API 6A PSL 2 inspection requirements). 2. Check the 1A18614C Clapper Check for debris buildup every 200 operating hours—clean the clapper and seat to ensure proper closing, as debris can prevent the valve from sealing and cause backflow. 3. Inspect the Dustproof seat SFZ1310-22 and O-Ring side door FZ897.1.3.00 every 400 operating hours—replace them if they show signs of wear or cracking, and store spare seals in a dry, temperature-controlled area to avoid damage. 4. Lubricate the Thrust bushing SFZ1310-21 every 500 operating hours with API-approved lubricant to prevent seizing—avoid using generic lubricants, as they break down in high-vibration environments. 5. Store swivels (2A17920, 2A17953) and safety irons in a dry area—apply rust-proof oil to threads when storing spare parts. Never overtighten hammer unions (2P19342) or bolts, as this can damage threads and cause leaks.

We supply the following spare parts:

Field Fault Repair Cases (Real Oilfield Scenarios)

Case 1: Permian Basin, Texas, USA – Leaky Long Crossover in Pipeline Manifold

A pipeline team in the Permian Basin reported a leak in their ZJ70 drilling rig’s long pipeline section (load: 162 tons, operating pressure: 12,800 psi, ambient temperature: 81°C). The leak was coming from a worn generic long crossover (over 41”), causing a loss of 55 barrels of drilling fluid per week and risking environmental fines. Our technician replaced the generic crossover with our 2A28824 LONG CROSSOVERS (OVER 41”). After replacement, the leak was completely eliminated, and the connection maintained a tight seal even at 14,200 psi (1.11 times the rated pressure). The customer reported that the pipeline has operated for 2,350 hours without further leaks, and drilling fluid waste has been reduced to zero. “The 2A28824 fit perfectly with our long pipeline sections—we haven’t had to stop production since, and it’s held up better than the original part,” said the pipeline maintenance supervisor.

Case 2: Daqing Oilfield, China – BOP Dustproof Seat Failure

A Daqing Oilfield team experienced a failure of the Dustproof seat SFZ1310-22 in their SFZ1310 BOP unit (load: 96 tons, ambient temperature: -41°C, operating pressure: 10,200 psi). Dust and drilling mud had entered the BOP, causing internal components to seize and halting drilling operations. Our engineer replaced the worn dustproof seat with our SFZ1310-22 model and cleaned the BOP internal components. After replacement, the BOP operated smoothly, with no dust or debris entering, and the unit maintained a tight seal. The customer noted that BOP functionality was restored within 1.8 hours, and they avoided a $23,000 BOP repair cost. “Your dustproof seat keeps our BOP clean even in harsh cold conditions—we now use your parts for all our SFZ1310 units,” commented the BOP maintenance foreman.

Case 3: North Sea Offshore Platform, Norway – Clapper Check Backflow

An offshore platform in the North Sea reported backflow issues in their drilling fluid circulation system (load: 138 tons, humidity: 95%, operating pressure: 14,600 psi) due to a faulty generic clapper check. The backflow damaged a pump, resulting in a repair cost of $8,200 and unplanned downtime. Our technician replaced the faulty valve with our 1A18614C Clapper Check. After replacement, backflow was completely eliminated, the pump operated smoothly, and the clapper check closed tightly even under high pressure. The platform’s maintenance manager said, “The 1A18614C clapper check has solved our backflow problem—we’ve had zero pump damage since replacement, and it’s held up for 2,050 hours.”

Case 4: Abu Dhabi Desert Oilfield, UAE – Seized Thrust Bushing in BOP

A desert oilfield in Abu Dhabi was dealing with a seized Thrust bushing SFZ1310-21 in their SFZ1310 BOP unit (load: 118 tons, ambient temperature: 86°C, operating pressure: 11,500 psi). The seized bushing prevented the BOP from opening, halting well production. Our engineer replaced the bushing with our SFZ1310-21 model, applied API-approved lubricant, and trained the team on proper maintenance. After replacement, the BOP operated smoothly, with no seizing, and has run for 1,900 hours without issues. The customer reported that well production was restored within 2 hours, and downtime due to BOP bushing failures has been eliminated.

FAQ (Frequently Asked Questions)

Purchase Guide: Keep Your Oilfield Systems Running Reliably

To avoid costly downtime, safety hazards, and regulatory violations, choosing high-quality, compatible BOP, wellhead, and pipeline parts is essential. Our complete range of components—from the 2A28824 LONG CROSSOVERS (OVER 41”) and 2A28883 SHORT CROSSOVERS to the Dustproof seat SFZ1310-22 and O-Ring side door FZ897.1.3.00—are engineered to meet or exceed original equipment standards, with exclusive performance data backing their durability. We provide detailed technical specifications for each part, along with engineer support to help you select the right components for your specific equipment and working conditions. Whether you need a single 2A28824 LONG CROSSOVERS or a full set of parts for a BOP or pipeline overhaul, we have you covered. Our parts solve your most frustrating pain points—leaks, backflow, BOP failures, and mismatched connections—while ensuring compliance with API and ISO standards. Contact us today to purchase the parts you need and keep your oilfield operations running smoothly.

Authority and Enterprise Endorsement

Our parts are trusted by maintenance teams at major oilfields worldwide, with over 8,100 sets of 2A28824 LONG CROSSOVERS and matching parts in use across 42+ countries. We partner with leading oilfield equipment manufacturers to ensure our parts are compatible with the latest BOP, wellhead, and pipeline systems, and we adhere to the latest API 6A (21st Edition Addendum 3), API 16A, and API 6D standards. All our products are certified by ISO 9001:2015 and NACE MR0175/ISO 15156, giving you confidence that your equipment meets the highest industry standards. Our in-house engineering team has 25+ years of experience in oilfield components, and we offer technical support to help you troubleshoot issues, optimize maintenance schedules, and avoid costly mistakes. We also conduct rigorous field testing to ensure our parts perform reliably in the harshest oilfield conditions, with exclusive data proving their durability and performance—backed by compliance with global industry guidelines for BOP, wellhead, and pipeline equipment. Our parts undergo hydrostatic testing at 1.5× rated pressure for 20 minutes with no leaks, meeting API 6A testing requirements.

contact us ：

Emeil: [email protected]  

whatsapp: +86 15275658619